Hansa C65 Скачать руководство пользователя | Manualshive

Страница: 6 / 42

background image

Hansa C65RX O&M Manual

–

OM-029 First Release 4/05/2021

© Hansa Chippers 2021

4

injuries.

Sound

Damage to hearing

Always wear hearing protection when operating the
machinery

Discharge material

Eye injury, minor cuts

Always wear safety glasses when operating the machinery

Do NOT

stand in front of the outlet chute

Do NOT

face the machinery in a place where the

outlet chute is directed on a hard surface

Feeding material

Cuts and scrapes

Wear tight fitting safety gloves
Wear tight fitting long sleeves and pants to cover bare skin
when operating the machinery

Weight of the chipper Straining, crushing

Place the machinery on level ground

Do NOT

attempt to move the machinery up/down

slopes unless is attached to a towing vehicle

Pinch points

Pinching, crushing

When opening/closing the inlet table, bonnet, or other
guard, it is recommended to use the handles provided

Petrol, oil, grease

Poisoning, skin irritation,
harmful vapours

Take care when handling petrol, oil and grease
Wash skin if contaminated with petrol, oil or grease

Do NOT

refuel the chipper in enclosed areas

Tracks

Crushing

Ensure area is clear of bystanders while moving the
machine.
Ensure the operator is controlling the machine from a point
where they have complete and unobscured vision of the
machine and its surroundings, especially in the direction of
travel.

Towing safety

Before towing, rotate the discharge chute to face either forwards or backwards, parallel with the direction of towing and
lock into position by; 1. Engaging lock pin and 2. Tightening outlet crank handle:

Lock the inlet table in the up position

Ensure the machine is sufficiently secured to the trailer

Ensure the machine is towed in accordance with local trailer transport regulations

Turn the machine off while towing

2. Tighten outlet crank handle

1. Engage lock pin (up)

«
...
4
5
6
7
8
...
»

Содержание C65











































Отзывы:

Нет отзывов

Похожие инструкции для C65

Pathfinder AWV Series

Бренд: Daikin Страницы: 92

Бренд: Garland Страницы: 136

Бренд: Cleveland Страницы: 18

Бренд: Gamma Страницы: 60

Бренд: Daikin Страницы: 228

Бренд: Moser Страницы: 116

Бренд: Remington Страницы: 128

Бренд: Remington Страницы: 134

Бренд: Remington Страницы: 160

Бренд: Andis Страницы: 2

Groom Clipper GC

Бренд: Andis Страницы: 1

Color Waves 23755

Бренд: Andis Страницы: 2

ElectraCOOL LA 600

Бренд: Advanced Thermoelectric Страницы: 24

Бренд: COOL HEAD Страницы: 48

PURESTREAM MINI-CUBE QBS 001 EAA Option

Бренд: FRIULAIR Страницы: 35

Бренд: PALSON Страницы: 11

Бренд: EIDER Страницы: 57

Бренд: York Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды