Hans Grohe ShowerTablet Select 700 13184 Series Скачать руководство пользователя страница 4

Страница: 4 / 44

Assembly

(see page 33)

Fault

Cause

Remedy

Insufficient water

- Supply pressure inadequate

- Check water pressure (If a pump has been installed

check to see if the pump is working).

- Regulator filter dirty

- Clean filter in front of the mixer and on the MTC-

thermo cartridge

- Shower filter seal dirty

- Clean filter seal between shower and hose

Crossflow, hot water being forced into cold water pipe,
or vice versa, when mixer is closed

- Backflow preventers dirty or leaking

- Clean backflow preventers, exchange if necessary

Spout temperature does not correspond with tempera-
ture set

- Thermostat has not been adjusted

- Adjust thermostat

- Hot water temperature too low

- Increase hot water temperature to 42 ºC to 65 ºC

Temperature regulation not possible

- thermo cartridge calcified

- Exchange thermo cartridge

- Hot and cold supplies are reversed

- change connections

Instantaneous heater didn't work with thermostat

- Filters are dirty

- Clean the filter / exchange filter

- check valve hasn't moved back

- Exchange check valves

- Flow limiter in handshower isn’t removed

- Remove flow limiter

Shower or spout dripping

- Dirt or sedimentation on valve seat, shut-off unit dam-

aged

- Exchange shut-off unit

Cleaning

(see page 37)

Spare parts

(see page 44)

Flow diagram

(see page 32)



Shower outlet



Outlet for additional consumer (free flow)

Dimensions

(see page 31)

Operation

(see page 43)

Maintenance

(see page 39)

• The mixer is equipped with check valves. The check valves must be

checked regularly according to DIN EN 1717 in accordance with
national or regional regulations (at least once a year).

• To guarantee the smooth running of the thermostat, it is necessary

from time to time to turn the thermostat from total hot to total cold.

Adjustment

(see page 37)

After the installation, the output temperature of the thermostat must be
checked. A correction is necessary if the temperature measured at the
output differs from the temperature set on the thermostat.

Safety Function

(see page 38)

The desired maximum temperature for example max. 42º C can be pre-
set thanks to the safety function.

Do not use silicone containing acetic acid!

Symbol description

Safety Notes

Gloves should be worn during installation to prevent crushing and cutting
injuries.

The product may only be used for bathing, hygienic and body cleaning pur-
poses.

Children as well as adults with physical, mental and/or sensoric impairments
must not use this product without proper supervision. Persons under the influ-
ence of alcohol or drugs are prohibited from using this product.

The hot and cold supplies must be of equal pressures.

Installation Instructions

• Prior to installation, inspect the product for transport damages. After it has been

installed, no transport or surface damage will be honoured.

• The pipes and the fixture must be installed, flushed and tested as per the applica-

ble standards.

• The plumbing codes applicable in the respective countries must be observed.
• During installation of the product by qualified trained personnel, make sure that

the entire fastening surface is even and smooth (no protruding seams or tile
offset), that the finish of the wall is suitable to apply the product and has no weak
points.

• The product is not designed to be used with steam baths!

Thermostatic mixer in conjunction with combination boilers

• If fitting a hand shower remove the water limiter from the shower.

Special information for UK

If installing this product with a pump, please be aware that it has to have negative
head switching. This product will not function with a positive head pump.

Technical Data

Operating pressure:

max. 1 MPa

Recommended operating pressure:

0,1 - 0,5 MPa

Test pressure:

1,6 MPa

(1 MPa = 10 bar = 147 PSI)
Hot water temperature:

max. 70°C

Recommended hot water temp.:

65°C

Centre distance: