manualshive.com logo in svg

Hanna Instruments pH 500 Series, Инструкция по эксплуатации

Поделиться
Скачать
Hanna Instruments pH 500 Series Скачать руководство пользователя страница 26

51

50

• No Slope:

- Check the electrode for cracks in glass stem or bulb

(replace the electrode if cracks are found).

- Make sure cable and connections are not damaged nor

lying in a pool of water or solution.

• Slow Response/Excessive Drift: soak the tip in the 

HI 7061

solution for 30 minutes, rinse thoroughly in distilled water
and then follow the Cleaning Procedure above.

• For ORP Electrodes: polish the metal tip with a lightly abra-

sive paper (paying attention not to scratch the surface)
and wash thoroughly with water.

Note

With industrial applications, it is always recommended to
keep at least one spare electrode handy. When anomalies
are not resolved with a simple maintenance, change the
electrode (and recalibrate the controller) to see if the prob-
lem is alleviated.

For refillable electrodes**: Refill the electrode with fresh electrolyte (

HI 7071

 for single

junction or 

HI 7082

 for double junction electrodes). Allow

the electrode to stand upright for 1 hour. Follow the Stor-
age Procedure above.

CLEANING PROCEDURE

General

Soak in Hanna 

HI 7061

 general cleaning

solution for approximately 30 minutes.

Removal of films, dirt or deposits on the membrane/junction:

Protein

Soak in Hanna 

HI 7073

 protein cleaning so-

lution for 15 minutes.

Inorganic

Soak in Hanna 

HI 7074

 inorganic cleaning

solution for 15 minutes.

Oil/grease

Rinse with Hanna 

HI 7077

 Oil & Fat cleaning

solution.

          IMPORTANT

After performing any of the cleaning procedures rinse the
electrode thoroughly with distilled water, drain and refill
the reference chamber with fresh electrolyte, (not neces-
sary for gel-filled electrodes) and soak the electrode in

HI70300

 storage solution for at least one hour before rein-

stalling it.

TROUBLESHOOTING

Evaluate your electrode performance based on the following.

• Noise (Readings fluctuate up and down) could be due to:

- Clogged/Dirty Junction: refer to the Cleaning Procedure

above.

- Loss of shielding due to low electrolyte level (in refillable

electrodes only): refill with 

HI 7071

 for single junction

or 

HI 7082

 for double junction electrodes.

• Dry Membrane/Junction: soak in 

HI 70300

 storage solu-

tion for at least 1 hour. Check to make sure the installation
is such as to create a well for the electrode bulb to con-
stantly remain moist.

• Drifting: soak the electrode tip in warm Hanna 

HI 7082

solution for one hour and rinse tip with distilled water (refill
with fresh 

HI7071

 for single junction electrodes and

HI7082

 for double junction electrodes if necessary).

• Low Slope: refer to the cleaning procedure above.

Содержание pH 500 Series


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды