Hanil Smart 15 Plus Скачать руководство пользователя страница 19

Страница: 19 / 24

Technical Support : +82-3452-8966 / [email protected]

19/21

6.2 Error Codes

6. Troubleshooting

Error

Message

Cause

Recommended Action

Imbalance
error

•Asymmetrical arrangement of
tubes.
•Different volume of sample .

• Check the tightness of rotor loading.
• Check the proper loading of tubes.
• Check the stable ground or worktable.

Over

speed

error

•2% over the set RPM.

•Incorrect tuning of motor and

controller.

• Check controller and motor.

• Switch power on/off and re-start.

Motor

over-heat

•Temp. hike inside of motor.

• Check the stator of motor.

• Switch power off, restart after 1 hour.

Motor

operation

error

•Motor operation error

• Check that the rotor is rotating through

the RPM measuring window

• Switch power on/off and re-start.

Door open

(Operating)

•Lid open during operation

• Switch the device off and contact

the Technical support team.

System

error

•System error

• Switch the device off and contact

the Technical support team.

E11

Motor
tempterature
sensor error !

•

Motor temperature sensor

error

• Switch power on/off and re-start.

E12

HI voltage

Error

•

High voltage

• Switch power on/off and re-start.

E13

Low voltage

Error

•

Low voltage

• Switch power on/off and re-start.

E15

RPM

sensing

error

•

RPM Sensor error

•

Rotor identification error

• Switch power on/off and re-start.

E17

Communi-

cation error

•

Occurs when Main and IO

board are disconnected

• Switch the device off and contact

the Technical support team.

Содержание Smart 15 Plus

























Результаты поиска

Содержание Smart 15 Plus

Отзывы:

Похожие инструкции для Smart 15 Plus

Бренды по названию

Популярные бренды

Hanil Smart 15 Plus, Руководство по эксплуатации

Результаты поиска

Содержание Smart 15 Plus

Отзывы:

Похожие инструкции для Smart 15 Plus

Бренды по названию

Популярные бренды