Hangar 9 Twist 3D .40 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 40

Hangar 9 Twist 3D .40 Скачать руководство пользователя страница 4

4

Warning

Additional Required Tools and Adhesives

Tools

• Canopy scissors
• Drill
• Drill bits: 1/16”, 3/32”, 1/8”, 9/64”, 5/32”
• Felt-tipped pen
• Flat blade screwdriver
• Foam: 1/2”
• Hobby knife
• Masking tape
• Paper towels
• Petroleum jelly
• Phillips screwdriver (large)
• Phillips screwdriver (small)
• Pliers
• Rubbing alcohol
• Ruler
• Sandpaper
• Soldering iron
• Square
• T-Pins

Adhesives

• 6-Minute Epoxy (HAN8000)
• 30-Minute Epoxy (HAN8002)
• Thin CA (PAAPT07)
• Medium CA (PAAPT01)
• CA Remover/Debonder (PAAPT16)
• Masking Tape (MMM20901)
• CA Remover/Debonder (PAAPT16)
• Canopy glue (Formula 560)

Other Required Items

• 2

1

/

4

" spinner (yellow)

• Epoxy Brushes (DUB345)
• File
• Measuring device (e.g. ruler, tape measure)
• Mixing Sticks for Epoxy (DUB346)
• Paper towels
• Rubbing alcohol
• Wax paper

An RC aircraft is not a toy! If misused, it can cause serious bodily harm and damage to property. Fly only in open
areas, preferably at AMA (Academy of Model Aeronautics) approved flying sites, following all instructions included
with your radio and engine.

Field Equipment Required

• Propeller (MAS1060)
• Fuel
• Glow Plug Wrench (HAN2510)

• Glow Plug Igniter with Charger (HAN7101)
• Glow Plug (HAN3001/3006)
• Manual Fuel Pump (HAN118)

«
...
2
3
4
5
6
...
»

Содержание Twist 3D .40









































Отзывы:

Нет отзывов