Hangar 9 Twist 3D .40 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 40

Hangar 9 Twist 3D .40 Скачать руководство пользователя страница 34

34

Section 14: Linkage Installation

Step 24

Make a 90-degree bend at the mark made in the
last step. Temporarily connect the pushrod to the
throttle arm. Check the movement of the throttle to
verify there is no binding at either low or high
throttle. If there is, make the necessary adjustment
to eliminate any binding.

Step 25

Secure the throttle pushrod to the servo arm using
a nylon wire keeper. Install the throttle servo arm
screw when complete.

Section 15: Canopy Installation

Required Parts

• Fuselage assembly

• Canopy

Required Tools and Adhesives

• Canopy glue (RC-56)
• Sandpaper (medium grit)

Step 1

Install a pilot of your choosing. Use epoxy or
Zap-A-Dap-A-Goo to secure the pilot.

Step 2

Position the canopy onto the fuselage so the
front edge of the canopy is 3

7

/

8

" forward of the

instrument panel. Draw a line around the canopy
using a felt-tipped pen so 3/8" of the canopy will
overlap onto the fuselage.

Photo for Step 2

«
...
32
33
34
35
36
...
»

Содержание Twist 3D .40









































Отзывы:

Нет отзывов