background image

5

Hangar 9 P-51D Mustang Sport 40 Assembly Manual

Radio Equipment Requirements - 

9-Channel Receiver

The following items are recommended when installing the 

9-Channel AR9000 receiver (SPMAR9000) in your aircraft:

DS821 Digital Sport Servo (5–8) 

 

JRPS821 

 

(Note: One less servo required for EP version)

3-inch Servo Extension (Retract)   

JSP98100

6-inch Servo Extension (5) (ESC, Ailerons)  JSP98020
9-inch Servo Extension (2) (Ailerons) 

JRPA097

Receiver Battery, 6-volt, 2700mAh   

JRPB5008

JR Chargeswitch   

 

 

JRPA004 or

JR Switch 

 

 

 

JRPA005

Ailerons: DS821 Servo (2)

• 6-inch Extension (plugged into receiver) (2)
• 9-inch Extension (connected to servo) (2)

Elevator: DS821 Servo

Rudder: DS821 Servo

Throttle: DS821 Servo

Note:  ESC will require a 6-inch extension plugged  

into the receiver

Optional Flaps: DS821 Servo (2)

• 6-inch Extension (plugged into receiver) (2)

Optional Retracts: DS821 Servo

• 3-inch Extension (plugged into receiver)

note

: Retracts can also use an MN48 servo 

(JSP20040) when using the included plywood servo 

adapter.

optional Retracts

Robart Spring Down includes prebent struts and air 

installation kit (HANP51)
23/4-inch (70mm) Main Wheels (HAN305)
Robart Air Pump (ROB164G)
DS821 Digital Sport Servo (JRPS821) or
MN48 Mini Servo (JSP20040)

Field Equipment Required

• Fuel (15% recommended)
• Long Reach Glow Plug Wrench (HAN2510)
• Metered Glow Driver with Ni-Cd & Charger (HAN7101)
• 2-Cycle Sport Plug (EVOGP1)
• Manual Fuel Pump (HAN118)

optional Field Equipment

• Self-stick weights, 6 oz (HAN3626)
• PowerPro 12V Starter (HAN161)
• 12V 7Ah Sealed Battery (HAN102)
• Power Panel (HAN106)
• Blue Block After Run Oil (EVOX1001)
• Cleaner and towels

Additional Required Tools

Drill 

File

Pin vise 

Pliers

Ruler 

Hobby scissors

Side cutters 

Epoxy brushes

Felt-tipped pen 

Rotary tool

Sanding drum 

String/dental floss

Mixing sticks 

Mixing cups

Paper towels 

Rubbing alcohol

Covering iron 

Small clamps

Hook and loop tape 

Pencil

Hobby knife with #11 blade  Medium grit sandpaper
Phillips screwdriver: #1, #2
Low-Tack Tape (MMM209034) 
Box end or open end wrench:  12mm
Hex wrench or ball driver: 3/32-inch
Drill bit:  1/16-inch (1.5mm), 5/64-inch (2mm),  

13/64-inch (5mm)

Additional Required Adhesives

Canopy Glue 

(PAAPT56)

Medium CA 

(PAAPT02)

Thin CA 

(PAAPT08)

Threadlock 

(PAAPT42)

30-Minute Epoxy, 8 oz 

(PAAPT39)

Hinge Glue 

(PAAPT55)

ultraCote® Covering Colors

• Black 

HANU874

• White 

HANU870

• Silver 

HANU881

• Cub Yellow 

HANU884

• True Red 

HANU866

• Olive Drab 

HANU904

using the Manual

This manual is divided into sections to help make assembly 

easier to understand, and to provide breaks between each 

major section. In addition, check boxes have been placed 

next to each step to keep track of each step completed. 

Steps with a single box (

) are performed once, while steps 

with two boxes (



) indicate that the step will require 

repeating, such as for a right or left wing panel, two servos, 

etc. Remember to take your time and follow the directions.

Before Starting Assembly

Before beginning the assembly of your model, remove 

each part from its bag for inspection. Closely inspect the 

fuselage, wing panels, rudder and stabilizer for damage. If 

you find any damaged or missing parts, contact the place of 

purchase.
If you find any wrinkles in the covering, use a heat gun or 

covering iron to remove them. Use caution while working 

around areas where the colors overlap to prevent separating 

the colors.

 

HAN100 – Heat Gun

HAN150 – Covering Glove

 

HAN101 – Sealing Iron

HAN141 –  Sealing Iron 

Sock

Содержание P-51D Mustang 40 ARF

























































Отзывы: