Hangar 9 P-51D Mustang 40 ARF Скачать руководство пользователя страница 4

Страница: 4 / 56

Hangar 9 P-51D Mustang Sport 40 Assembly Manual

Important Information

Regarding Warranty

Please read our Warranty and Liability Limitations section on

page 49 before building this product. If you as the purchaser

or user are not prepared to accept the liability associated

with the use of this Product, you are advised to return this

Product immediately in new and unused condition to the

place of purchase.

Recommended Setup–2-Stroke glow

• Evolution

.46NX with Muffler (EVOE0461)

• Evolution Propeller 11 x 5 (EVO10050) or

10 x 6 (EVO11060)

• 2

-inch 2-blade Spinner, Red (DUB292)

• Exhaust Diverter (DUB697) (Optional)

Recommended Setup–4-Stroke glow

• Saito 82 (SAIE082aGK)
• 13 x 8 propeller (EVOE13080)
• 2

-inch 2-blade Spinner, Red (DUB292)

Recommended Setup–

Electric Power (EP)

• E-flite

Power 46 BL Outrunner Motor (EFLM4046A)

• 60-Amp Pro Switch-Mode BEC Brushless ESC

(EFLA1060)

• Thunder Power 4S 3850–4500mAh Li-Po Battery Pack
• APC Propeller 13x6.5-inch (APC13065E) or

14x7 (APC14070E)

• 2

-inch 2-blade Spinner, Red (DUB292)

Transmitter Requirements

The P-51D Mustang requires a minimum of a 6-channel

radio to operate all the functions of your aircraft. We suggest

the following radio systems available through Horizon Hobby

or your local hobby distributor.

Spektrum DX6i

SPM6600

Spektrum DX7

SPM2710

JR Systems X9303 2.4GHz

JRP2915

JR Systems 12X 2.4GHz

JRP1200

Radio Equipment Requirements -

6-Channel Receiver

The following items are recommended when installing the

6-Channel AR6200 receiver (SPMAR6200) in your aircraft:

DS821 Digital Sport Servo (5–8)

JRPS821

(Note: One less servo required for EP version)

3-inch Servo Extension (Retract)

JSP98100

6-inch Servo Extension (ESC)

JSP98020

9-inch Servo Extension (2) (Ailerons)

JRPA097

Y-harness (2)

JSP98020

Receiver Battery, 6-volt, 2700mAh

JRPB5008

JR Chargeswitch

JRPA004 or

JR Switch

JRPA005

Ailerons: DS821 Servo (2)

• Y-harness (plugged into receiver)
• 9-inch Extension (connected to servo) (2)

Elevator: DS821 Servo

Rudder: DS821 Servo

Throttle: DS821 Servo

Note: ESC will require a 6-inch extension plugged

into the receiver

Optional Flaps: DS821 Servo (2)

• Y-harness (plugged into receiver)

Optional Retracts: DS821 Servo

• 3-inch Extension (plugged into receiver)

note

: Retracts can also use an MN48 servo

(JSP20040) when using the included plywood servo

adapter.

Radio Equipment Requirements -

7-Channel Receiver

The following items are recommended when installing the

7-Channel AR7000 receiver (SPM6070) in your aircraft:

DS821 Digital Sport Servo (5–8)

JRPS821

(Note: One less servo required for EP version)

3-inch Servo Extension (Retract)

JSP98100

6-inch Servo Extension (3) (ESC, Ailerons) JSP98020
9-inch Servo Extension (2) (Ailerons)

JRPA097

Y-harness

JSP98020

Receiver Battery, 6-volt, 2700mAh

JRPB5008

JR Chargeswitch

JRPA004 or

JR Switch

JRPA005

Ailerons: DS821 Servo (2)

• 6-inch Extension (plugged into receiver) (2)
• 9-inch Extension (connected to servo) (2)

Elevator: DS821 Servo

Rudder: DS821 Servo

Throttle: DS821 Servo

Note: ESC will require a 6-inch extension plugged

into the receiver

Optional Flaps: DS821 Servo (2)

• Y-harness (plugged into receiver)

Optional Retracts: DS821 Servo

• 3-inch Extension (plugged into receiver)

note

: Retracts can also use an MN48 servo

(JSP20040) when using the included plywood servo

adapter.

The Spektrum trademark is used with permission

of Bachmann Industries, Inc.

Содержание P-51D Mustang 40 ARF

























































Результаты поиска

Содержание P-51D Mustang 40 ARF

Отзывы:

Похожие инструкции для P-51D Mustang 40 ARF

Бренды по названию

Популярные бренды

Hangar 9 P-51D Mustang 40 ARF, Инструкция по сборке

Результаты поиска

Содержание P-51D Mustang 40 ARF

Отзывы:

Похожие инструкции для P-51D Mustang 40 ARF

Бренды по названию

Популярные бренды