Hangar 9 CAP 232G ARF Скачать руководство пользователя страница 8

Страница: 8 / 36

Required Parts

•.Elevator.(left.and.right).

•.Fin

•.Rudder.

•.Hinges.(21)

•.Wing.panel.(right.and.left)
•.Aileron.(left.and.right)
•.Stabilizer.(left.and.right)

Required Tools and Adhesives

•.Syringe.

•.Sandpaper.(coarse)

•.Toothpicks.

•.Razor.saw

•.Petroleum.jelly.

•.Straight.edge/ruler

•.Felt-tipped.pen.

•.Scissors

•.Hobby.knife.w/#11.blade
•.Covering.Iron.(HAN101)
•.Clear.UltraCote®.(HANU964)
•.30-minute.epoxy.or.Pacer.Hinge.Glue.(PT-55)

Properly.hinging.the.control.surfaces.on.giant-scale.

models.is.vitally.important..Poorly.installed.hinges.affect.

the.model’s.precision.and.control.response.and.can.also.

be.dangerous..Each.and.every.hinge.needs.to.be.securely.

bonded.in.place.in.both.the.flying.surface.and.the.control.

surface..The.hinge.pivot.points.need.to.be.exactly.parallel.

to.each.other.and.precisely.located.on.the.center.of.the.

hinge.line.



Step 1

Sand.each.end.of.the.hinge.point.using.coarse.sandpaper..

This.will.improve.the.bond.of.the.epoxy.to.the.hinge..

Apply.a.thin.coat.of.Petroleum.jelly.to.the.hinge.point.to.

prevent.the.epoxy.from.gluing.the.hinge.surface.



Step 2

Mix.one.ounce.of.30-minute.epoxy..Using.a.glue.syringe.

or.toothpick,.place.a.sufficient.amount.of.30-minute.

epoxy.into.one.of.the.hinge.pockets.in.the.aileron.leading.

edge.only..Install.one.of.the.hinge.points.until.the.hinge.

pin.center.is.flush.with.the.leading.edge.of.the.aileron..

Some.epoxy.should.ooze.out.of.the.pocket.as.the.hinge.is.

installed..If.not,.remove.the.hinge.and.apply.more.epoxy..

After.gluing.a.few.hinges,.you’ll.get.the.hang.of.just.how.

much.epoxy.is.needed..Wipe.away.any.excess.epoxy.with.

rubbing.alcohol..Re-check.that.the.center.of.the.hinge.

pin.is.flush.and.parallel.with.the.leading.edge..Continue.

installing.hinges.in.the.leading.edge.of.the.aileron..The.

control.surfaces.(ailerons).will.be.installed.after.the.epoxy.

is.fully.cured.

Note

:.Be.sure.that.the.hinge.pivot.pins.are.

parallel.and.flush.to.the.aileron.leading.edge..

It’s.important.to.frequently.mix.a.fresh.batch.

of.30-minute.epoxy.in.order.to.achieve.good.

glue.joint.penetration..If.you.notice.the.epoxy.

becoming.thicker,.then.mix.a.new.batch.

Hint

:.You.can.also.use.Pacer.PT-55.

Hinge.Glue.to.glue.the.hinges..Follow.

the.instructions.here.as.well.as.on.the.

glue.bottle.to.achieve.the.best.results.

Section 1 – Hinging the Control Surfaces

Содержание CAP 232G ARF





































Результаты поиска

Содержание CAP 232G ARF

Отзывы:

Похожие инструкции для CAP 232G ARF

Бренды по названию

Популярные бренды

Hangar 9 CAP 232G ARF, Инструкция по сборке

Результаты поиска

Содержание CAP 232G ARF

Отзывы:

Похожие инструкции для CAP 232G ARF

Бренды по названию

Популярные бренды