Hangar 9 85cc Sukhoi SU-26MM Скачать руководство пользователя страница 11

Страница: 11 / 41

Hangar 9 3.1m Sukhoi SU-26MM ARF Assembly Manual

Elevator Servos Installation

Required Parts

Elevator panel

4-40 screws (8)

Locknuts (8)

Ball link (8)

Control horns (4) (3D elevator setup only)
2

-inch elevator pushrod (4)

Required Parts (not included)

JR 8911HV or similar digital servo (2) or (4)
JR 1.5-inch servo arm (2) or (4)
JR heavy-duty servo extension, 48-inch (2)

Required Tools and Adhesives

Pin vise

Iron

Thin CA

Phillips screwdriver: #1

Drill bit: 1/16-inch

30-minute epoxy

String (Dental floss)

Masking tape

Adhesive-backed hook and loop
3/32-inch ball driver

Hobby knife

2.5mm ball driver

Note: Elevators will be set up for both precision and 3D

flying. Due to extra demand in power and deflection of

3D flying, two servos will be used for that style.

Precision Setup



1. For precision setup one servo per elevator is used.

Prepare the servo by installing the rubber grommets and

brass eyelets.

Servo needs to be installed in such way that output shaft is

towards the leading edge of the stab. The servo arm needs

to be 1.25 inch; if in case of using a JR aluminum servo

arm, this would be the third outermost hole.



2. Mount the servo screws and back them out.



3. To harden the servo mounting holes in the bay

apply some thin CA in the hole. Wait until CA is dry before

installing the servo.



4. Mount the servo so the output shaft is towards the

leading edge of the stab.



5. Prepare the ball link and pushrod. Attach the ball

link to the control horn using a 2.5mm ball driver and hold

the locknut with help of a vise grip or nut driver.



6. Connect the ball link to the 1.25-inch hole on a JR

aluminum servo arm. This would be the third outermost hole

from the center of the arm. Mount the servo arm parallel to

the elevator hinge line. Use threadlock on the center servo

arm screw. Use a 48-inch JR Heavy-Duty extension from

elevator to receiver.

Содержание 85cc Sukhoi SU-26MM










































Результаты поиска

Содержание 85cc Sukhoi SU-26MM

Отзывы:

Похожие инструкции для 85cc Sukhoi SU-26MM

Бренды по названию

Популярные бренды

Hangar 9 85cc Sukhoi SU-26MM, Инструкция по сборке

Результаты поиска

Содержание 85cc Sukhoi SU-26MM

Отзывы:

Похожие инструкции для 85cc Sukhoi SU-26MM

Бренды по названию

Популярные бренды