Hangar 9 85cc Sukhoi SU-26MM Скачать руководство пользователя страница 5

Страница: 5 / 41

Hangar 9 3.1m Sukhoi SU-26MM ARF Assembly Manual

3.1m Sukhoi Operating Recommendations

• Inspect your model before every flight to make certain it

is airworthy.

• Be aware of any other radio frequency user who may

present an interference problem.

• Always be courteous and respectful of other users of

your selected flight area.

• Choose an area clear of obstacles and large enough to

safely accommodate your flying activity.

• Make certain this area is clear of friends and spectators

prior to launching your aircraft.

• Be aware of other activities in the vicinity of your flight

path that could cause potential conflict.

• Carefully plan your flight path prior to launch.
• Abide by any and all established AMA National Model

Aircraft Safety Code.

Important Information

Regarding Warranty

Please read our Warranty and Liability Limitations section

before building this product. If you as the purchaser or user

are not prepared to accept the liability associated with the

use of this Product, you are advised to return this Product

immediately in new and unused condition to the place of

purchase.

Using the Manual

This manual is divided into sections to help make assembly

easier to understand, and to provide breaks between each

major section. In addition, check boxes have been placed

next to each step to keep track of each step completed.

Steps with a single box (



) are performed once, while

steps with two or more boxes (



) indicate that the step

will require repeating, such as for a right or left wing panel,

two servos, etc. Remember to take your time and follow the

directions.

UltraCote® Covering Colors

• Cream

HANU878

• Orange

HANU877

• Pearl Purple

HANU847

• Silver

HANU881

Recommended Setup–2-Stroke Gas

• DA150
• DA-170

Recommended Spinner

5-inch purple Tru-Turn Ultimate Style with solid back

plate.

• DA150, TT-5052-B-M-3W120-AP
• DA-170, TT-5052-B-M-DA170-AP

Optional Tuned Pipe and Canister

Installation

If you are installing the optional tuned pipe, the following

items will be required:

• 50mm drop header, 14-inch long for tuned pipe (MTW,

RE3) and 8 to 9-inch for canister (MTW TD110)

• Clamps
• Couplers

Transmitter Requirements

The 3.1m Sukhoi requires a minimum of a 4-channel radio

to operate all the functions of your aircraft. However to get

the best performance from the Sukhoi, a radio with mixing

functions is recommended. We suggest the following radio

systems available through Horizon Hobby or your local

hobby distributor.

Spektrun DX8

SPM8800

JR Systems X9503 2.4GHz

JRP2930

JR Systems 11X 2.4GHz

JRP1100

JR Systems 12X 2.4GHz

JRP1200

Radio Equipment Requirements

The following items are recommended when installing the

9-Channel AR91000 (SPMAR9100) in your aircraft:

DS8911HV Digital Servo (8–12)

JRPS8911HV

JR 537 Servo (1)

JRPS537

12-inch Servo Extension (2) (Ailerons)

JRPA098

18-inch Servo Extension (2) (Ailerons)

JRPA099

24-inch Servo Extension (1) (Throttle)

JRPA102

36-inch Servo Extension (2) (Ailerons)

JRPA103

48-inch Servo Extension (2) (Rudder)

JRPA104

48-inch Servo Extension (2) (Elevators)

JRPA104

(2) Receiver Packs, 4000mAh Spektrum

SPMB4000LP

Ignition Pack 2000mAh Spektrum

SPMB2000LP

JR Charge Switch

JRPA004

JR MatchBox (4)

JRPA900

The Spektrum trademark is used with permission

of Bachmann Industries, Inc.

Содержание 85cc Sukhoi SU-26MM










































Результаты поиска

Содержание 85cc Sukhoi SU-26MM

Отзывы:

Похожие инструкции для 85cc Sukhoi SU-26MM

Бренды по названию

Популярные бренды

Hangar 9 85cc Sukhoi SU-26MM, Инструкция по сборке

Результаты поиска

Содержание 85cc Sukhoi SU-26MM

Отзывы:

Похожие инструкции для 85cc Sukhoi SU-26MM

Бренды по названию

Популярные бренды