H&S 6128 Скачать руководство пользователя страница 34

Страница: 34 / 46

Your H&S Merger was manufactured with operator safety in mind. Located on the merger are various

decals to aid in operation, and warn of danger or caution areas. Pay close attention to all the decals on

your windrow merger.

DO NOT REMOVE ANY OF THESE DECALS. IF DECALS ARE LOST, DAMAGED,

OR IF YOUR WINDROW MERGER IS REPAINTED, REPLACE THE DECALS.

REMEMBER: DECALS ARE FOR YOUR PROTECTION AND SAFETY.

-32-

DECAL LOCATION

Part #

Qty. Description

311

Patent Numbers

1494L

Danger - Rotating Driveline

1494P

Danger - Maintain Safe Clearance

1906C

Warning - Stay Clear

5896B

Danger - Rotating Driveline

9194A

No Step-Stay Clear

11599

Warning - Do Not Go Near Leaks

12502A

Danger - Stay Clear of Extension

31401

Danger - Stay Clear of Merger

32597A

Do Not Operate w/Decal Exposed

54033

Made In America (4 1/2”)

72203A

Warning - Help Avoid Injury

73101

Danger - Stay Clear of Moving Parts

82602

Warning - Crushing Hazard

82907L

Danger - Never Allow Riders

83773

H&S Branding Decal

83774

H&S Branding Decal

83775

6128 Model Number

84044

FEMA

84045

H&S Since 1967

88994

Control Box Decal - Do Not Run Belts

093020

Grease

DC32211A

Warning - Stay Clear Contact With Tines

DC32211B

Warning - Slag Generated By Heating

DCRED

2” x 9” Red Reflector

DCAMB

2” x 9” Amber Reflector

Содержание 6128















































Результаты поиска

Содержание 6128

Отзывы:

Похожие инструкции для 6128

Бренды по названию

Популярные бренды

H&S 6128, Руководство оператора

Результаты поиска

Содержание 6128

Отзывы:

Похожие инструкции для 6128

Бренды по названию

Популярные бренды