Handicare PUMA KINETIC Скачать руководство пользователя | Manualshive

Страница: 36 / 99

background image

Maintenance

36

Version 2011v1

EBAPUM-020707040-nl.doc

3.6.4

Replacing the neutral cable

•

See fig. 020707060.

The neutral cable should be replaced as follows:

•

Remove the side cover. See 'removing the covers'.

•

Loosen nut (A) with a spanner with a key width of 10
mm.
After this, the inner cable (B) of the neutral can be
pulled away from the outer cable (C) from the side of
the drive unit.
If necessary, the outer cable can also be removed
now.

•

Take the nipple (D) from the inner cable by
unscrewing screw (E) using a screwdriver.

•

A new inner and/or outer cable should be placed in
reverse order.

Grease the cable lightly before pushing it into
the outer cable, in order to easily move it in
and out and protect it against oxidation.

•

Carefully adjust the neutral, so that it will operate perfectly.
This is done by adjusting the adjusting nipples (F or G).

EBAPUM-020707060-nl.doc

3.6.5

Replacing the parking brake

If the parking brake of a drive unit is faulty, the entire drive unit must be replaced.
It is not permitted to replace the parking brake.

With respect to replacing the parking brake the same instructions apply as for replacing the drive unit, see
'replacing drive unit'.

In connection with agreements concerning guarantees with the supplier of the drive unit, it is NOT
permitted to take the drive unit apart: every part of the drive unit delivered loose will be immediately
returned and the guarantee stipulations will become null and void.

EBAYES-020707050-en.doc

3.7

Electronic components

The Puma Kinetic is driven by the extensive 'DX' electronics, which comprise the following components:

•

Controller

•

Power module in the carrier

•

LM/CLAM module in the carrier

Before doing work on the electronic system the automatic safety fuse must be switched off by
pushing the button on the side of the wheelchair.

EBAPUM-020708000-nl.doc

F

D

B

C

E G

A

020707060

«
...
34
35
36
37
38
...
»

Содержание PUMA KINETIC




































































































Отзывы:

Нет отзывов

Похожие инструкции для PUMA KINETIC

Бренд: PRO ACTIV Страницы: 48

Бренд: Rehasense Страницы: 17

Otto Bock Back 1

Бренд: Otto Bock Страницы: 77

Бренд: Frontier Страницы: 35

Бренд: B+B Страницы: 38

Бренд: Permobil Страницы: 100

Бренд: Küschall Страницы: 44

Anchor Bath Chair

Бренд: Circle Specialty Страницы: 4

Бренд: Vermeiren Страницы: 7

Бренд: Switch-it Страницы: 2

Бренд: NRS Healthcare Страницы: 4

Бренд: AAT Страницы: 32

Leon F Kameleon

Бренд: Karma Страницы: 136

Бренд: Quickie Страницы: 156

Бренд: B&S Страницы: 12

Бренд: Vermeiren Страницы: 16

Бренд: Vermeiren Страницы: 104

Бренд: Sopur Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды