Handicare PUMA KINETIC Скачать руководство пользователя страница 28

Страница: 28 / 99

Maintenance

Version 2011v1

box..

EBAPUM-010701000.nl.doc

3.2.1

Replacing the batteries

•

See fig. 010701010.

If the capacity of the batteries is reduced to the extend that
the wheelchair can only make very short trips, or even none
at all, the batteries are at the end of their lifespan. Replace
them as soon as possible.

•

Contact your dealer who can advise
you what type of batteries are best
suitable for the wheelchair.

•

Avoid damage to the batteries when
replacing them: this may cause the
batteries to start leaking.

The batteries should be replaced as follows:

•

Switch off the wheelchair.

•

Switch off the automatic safety fuse. See 'Automatic
safety fuse' and ‘Malfunctions’.

•

Loosen the caps (A).

•

Raise the lid (B) a little at the back, and carefully slide it off the battery box.

•

Loosen the bolt from the negative (-) pole (C) and remove the battery clamp from the battery pole.

•

Now loosen the bolt from the positive (+) pole (D) and remove the battery clamp from the battery pole.

•

Then loosen the bolts from the battery clamps (E and F) from the power cable (G) and remove the
cable.

•

Lift the back battery (H) from the battery box using the carrying belts.

•

Slide the front battery (I) to the back, and take it out of the battery box as well.

New batteries are placed in the reverse order.

As soon as the new batteries are placed and the battery box is closed, the batteries must be
charged.

EBAPUM-010701010.nl.doc

3.2.2

Cleaning the batteries

Dry batteries:

These are in principle maintenance free. Nonetheless, attention must be paid to the following:

•

Keep the batteries clean and dry: dirt and water can cause a leak, so that the capacity of the batteries
will decrease.

•

Cleaning the poles: after cleaning, grease them with acid-free Vaseline.

•

Wet batteries:

These require maintenance:

•

See ‘Battery maintenance’.

•

They should be cleaned in the same way as dry batteries.

Never completely deplete the batteries! This can seriously damage the batteries and considerably
decrease their lifespan.

EBAPUM-010701020.nl.doc

010701010

Содержание PUMA KINETIC




































































































Результаты поиска

Содержание PUMA KINETIC

Отзывы:

Бренды по названию

Популярные бренды

Handicare PUMA KINETIC, Руководство по обслуживанию

Результаты поиска

Содержание PUMA KINETIC

Отзывы:

Бренды по названию

Популярные бренды