handi quilter HQ 24 Fusion Скачать руководство пользователя страница 2

Страница: 2 / 30

HQ Fusion

™

User Manual 1.0

Page 1

Safety Section

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Please note:

Do not operate your HQ Fusion

™

quilting machine until you have completely read the information

contained in this manual. Please keep all packaging and order information for warranty purposes.

1. The HQ Fusion

is very heavy. Never attempt to lift it alone – always use two people when lifting.

2. Always unplug the HQ Fusion™ from the electrical outlet when performing any maintenance, changing the

needle, removing thread locks, or when left unattended.

3. Keep fingers away from all moving parts. Use caution around the needle or sharp external components.

4. Change the needle often. Do not use bent or dull needles.

5. Switch the power off when making any adjustments in the needle or bobbin area, such as threading the

needle, installing the bobbin case, or when oiling or cleaning.

6. Never drop or insert foreign objects into any opening.

7. The HQ Fusion™ should only be used indoors away from moisture.

8. The HQ Fusion™ should not be stored or used in extreme temperatures.

9. Use the HQ Fusion™ only for its intended use as described in this manual.

10. Use only attachments recommended by the manufacturer.

11. To disconnect from the wall outlet, push the switch to the off position, then remove the plug from outlet pulling

from the plug, not the cord. Never operate the HQ Fusion™ if the cord is damaged or not working correctly. If

a mechanical or electrical problem is encountered, return the HQ Fusion™ to the nearest authorized service

center or the manufacturer for examination, repair, electrical or mechanical adjustment.

12. It is not recommended that the HQ Fusion™ Quilting Machine be used with any machine quilting frame other

than those recommended or manufactured by Handi Quilter.

Quick Facts

Description

Specification

Sewing Speed – Manual Mode

110 – 2200 SPM

Sewing Speed – Regulated Mode

0 – Full Speed

Needle Bar Stroke

35.3 mm

Sewing Foot Stroke/Lift

5 mm

Needle System

135x7 Standard 134 R Long Scarf

Needle Sizes

14/90 – 19/120

Lubricating Oil & Greases

Kluber Lubrication

Dimensions of Sewing Machine Throat

9.625

‖ x

24.0

0‖

Rate Voltage/Power Consumption

90 – 264 V

, 47 – 63 Hz, 400 Watts

Power Consumption of LED Lights

24 Watts

Hook System

Custom Manufactured, Rotary, Large Bobbin

Bobbin Type

Class M

Motor Type

Brushless DC

Automatic Needle Positioning

Up and down, full stitch and half stitch

Disclaimer

Handi Quilter and its Representatives are in no way legally responsible or liable for
damage to the HQ Fusion

™

when used improperly or not in accordance with the

guidelines stated in this manual or when used on Machine Quilting Frames not
recommended by Handi Quilter.

Содержание HQ 24 Fusion































Результаты поиска

Содержание HQ 24 Fusion

Отзывы:

Похожие инструкции для HQ 24 Fusion

Бренды по названию

Популярные бренды

handi quilter HQ 24 Fusion, Руководство пользователя

Результаты поиска

Содержание HQ 24 Fusion

Отзывы:

Похожие инструкции для HQ 24 Fusion

Бренды по названию

Популярные бренды