background image

02/10/2015

www.HandiQuilter.com

HQ Fusion User Manual  | 9

To install the front handles

1. 

Locate the three long bolts and the appropriate hex wrench. Tilt the screen forward. 

 

2. 

Line up the holes on top of the handles with the pre-drilled holes on top of the machine.  

 

3. 

Slide a single bolt into one of the holes until it stops. Hand-tighten the bolt enough to secure the 

handles to the top of the machine, but still allow you to rotate the handles.  

 

4. 

Secure the short 9-pin handlebar serial cable to the serial port (

see diagram B, #20

) on the back 

casing of the machine. 

 

 

NOTE

: You may need to rotate the handle slightly to allow access to the finger screws.  

 

5. 

Use the finger screws to tighten the 9-pin connector in position.  If necessary, a flat screwdriver may 

be used to gently secure the connector.

 

6. 

Rotate the handles back to their correct position and insert and hand tighten the remaining two 

handlebar bolts. Use the included 5 mm Hex wrench to securely fasten the handles to the front of  

the machine. 

Installing the Rear Handles

 

U

CAUTION

: Check that the HQ Fusion is unplugged from the electrical outlet. All power to the 

machine must be turned off when installing the back handles. Failure to do so can result in damage 

to the machine.

To install the rear handles

The rear handlebar comes mounted with three screws to the L-bracket. 

1. 

Line up the two holes in the L- bracket with those on the rear of the machine. Slide the short bolts 

into holes until they stop. Hand tighten, and then use the Hex wrench to securely fasten the handles 

to the back of the machine.

 

2. 

Once the two bolts are in place, plug the 9-pin connector into the serial port underneath the rear 

handles (

see diagram C, #32

). Ensure the pins are lined up so they are not damaged when the plug is 

pushed in.  Push the plug securely in place.

 

Â

IMPORTANT

: After the handles have been completely installed and plugged in, test them by turning 

on the HQ Fusion. (You will not be able to turn on the machine until the front handlebars have been 

installed.) If nothing is displayed, press the display power button on the top right of the touch-

screen display. If the display still does not turn on, check that the handle bar cable on the side of 

the machine is plugged in securely, that your machine is turned on, and that the power cord is 

plugged into the machine as well as a power source.

Содержание Fusion QM32469















































Отзывы: