Hand Held Products Dolphin 7200 Скачать руководство пользователя страница 37

Страница: 37 / 179

C H A P T E R 2 D O L P H I N B A S I C S

NiMH Battery Pack

The 3.6V, 1500 mAh Nickel-Metal-Hydride (NiMH) battery pack is the

primary power source for the Dolphin. Other Nickel-Metal-Hydride

batteries may be approved by Hand Held Products, Inc. to work with your

Dolphin. Contact Hand Held for more information.

The 1500 mAh NiMH battery is designed to operate in temperature range

of –10 to 50

C (14 to 122

F). For maximum performance, charge the batteries

between 10 and 35

C (50 and 95

F).

WARNING

: Although the Dolphin 7200 terminal is received with the battery inserted, it is

NOT

ready for charging and/or deep-cycling. Remove the plastic insulator located between the

terminal and battery connectors. Failure to remove the insulator may result in damages to the terminal.

Performance specifications for a fully charged 1500 mAh NiMH battery (using power

management function calls within application):

Up to 20 hours of usage in a Dolphin Batch terminal with a full battery charge

Up to 10 hours of usage in a Dolphin RF terminal with a full battery charge

Up to 20 hours of usage in a Dolphin 2D terminal with a full battery charge

Keep a charged battery pack in the Dolphin at all times to conserve the internal back-

up battery. When you remove a battery pack, insert another battery pack in the

Dolphin. The internal battery will prematurely discharge if there is not at least a

partially charged battery in the terminal.

Servicing the Battery Pack

For maximum battery life, Hand Held Products recommends that you deep-cycle the

battery

twice

before initial use. It is also recommended that you service, or calibrate

the battery once per month. To deep cycle, insert the battery into the HomeBase

auxiliary battery well. Then, push and hold the

Service Aux Batt

button for at least 4

seconds. For more information, see the section on the

Service Aux Batt

feature of the

HomeBase in Chapter 7.

You may also deep cycle the battery using the CycleBat battery utility conditioning

software which is available from the Partners area of the Hand Held Products website,

http://www.hhp.com/

. More information on this utility is available from the help file

that comes with the software.

N O T E

Keep a charged

battery pack in the

Dolphin at all times to

conserve the internal

back-up battery.

N O T E

For maximum battery

life, Hand Held

Products recommends

that you deep-cycle

(service) the battery

twice

before initial use

and then, once a month

thereafter.

Содержание Dolphin 7200




















































































































































































Результаты поиска

Содержание Dolphin 7200

Отзывы:

Похожие инструкции для Dolphin 7200

Бренды по названию

Популярные бренды

Hand Held Products Dolphin 7200, Руководство пользователя

Результаты поиска

Содержание Dolphin 7200

Отзывы:

Похожие инструкции для Dolphin 7200

Бренды по названию

Популярные бренды