Hand Held Products Dolphin 7200 Скачать руководство пользователя страница 26

Страница: 26 / 179

C H A P T E R 2 D O L P H I N B A S I C S

System Features

CPU

The Dolphin’s computing power is provided by a highly integrated AMD ELAN

SC310 386SX 33 MHz microprocessor.

Disk Drives

The Dolphin contains two disk drives that provide storage for system files,

applications, and data. A third drive is also present if you purchase the FLASH

expansion option.

Drive A

Drive A contains a 120K executable FLASH EEPROM to store system utilities and to

initialize the boot process. This drive is read-only and is not usable by the

developer/end-user.

Drive C

Drive C is an 8MB FLASH virtual hard drive used for program and data storage.

Drive D

If you add the expanded memory module to your Dolphin Batch terminal, it will

appear as Drive D. Eight (8)MB of additional FLASH memory can be added via the

FLASH expansion module.

Note: This option is only available for the Dolphin batch and

Dolphn iButton terminals.

Front Panel Physical Features

This section describes features on the Dolphin’s front panel. The alphanumeric and

numeric Dolphins have identical back panels.

Light Emitting Diodes (LED)

The red LED located at the upper right corner of the LCD display is labeled ‘SCAN’.

This LED illuminates when the user presses the ON/KEY key and activates the scan

engine.

The green LED located at the upper left corner of the LCD display is labeled

‘DECODE.’ This LED illuminates when the bar code software successfully decodes a

bar code. Both LEDs are software programmable.

N O T E

Drive C is an image of

the A drive and not a

physical drive.

Содержание Dolphin 7200




















































































































































































Результаты поиска

Содержание Dolphin 7200

Отзывы:

Похожие инструкции для Dolphin 7200

Бренды по названию

Популярные бренды

Hand Held Products Dolphin 7200, Руководство пользователя

Результаты поиска

Содержание Dolphin 7200

Отзывы:

Похожие инструкции для Dolphin 7200

Бренды по названию

Популярные бренды