background image

3 - 4

2020/3820 User’s Guide

Scanner Trigger Modes

Manual/Serial Trigger, Low Power

You can activate the scanner either by pressing the trigger, or using a serial 
trigger command (see 

"Trigger Commands"

on page 10-4).  When in manual 

trigger mode, the scanner scans until a bar code is read, or until the trigger is 
released. 

When in serial mode, the scanner scans until a bar code has been read or until 
the deactivate command is sent.  In serial mode, the scanner can also be set to 
turn itself off after a specified time has elapsed (see 

Read Time-Out (Serial 

Trigger Mode)

, which follows).

Read Time-Out (Serial Trigger Mode)

Use this selection to set a time-out (in milliseconds) of the scanner’s trigger when 
using serial commands to trigger the scanner.  Once the scanner has timed out, 
you can activate the scanner either by pressing the trigger or using a serial 
trigger command.  After scanning the Read Time-Out bar code, set the time-out 
duration (from 0-300,000 milliseconds) by scanning digits on the 

Programming 

Chart

 inside the back cover, then scanning Save.  

Default = 300,000 ms.

Scanner Power Time-Out Timer

Note: The Scanner Power Time-out Timer option only applies to Manual/Serial 

Trigger.

When there is no activity within a specified time period, the scanner enters low 
power mode.  Scan the appropriate Scanner Power Time-Out bar code to 
change the time-out duration (in seconds).

* Manual/Serial Trigger

Read Time-Out

Содержание 3820





















































































































































































Отзывы: