background image

 

              

User Manual MCx-B-xxxAx-8.09 

 

 

Page 8 of 10

                                                                                                                                      

www.hanbayinc.com | 1 800 315 4461        

Rev.2020.3                                                                                                                                                                                              

 

[email protected] 

 
Speed and Torque of MC

M

-B-xxxAx Actuators       

NOTE

: If actuator is MC

K

-B-xxxAx, divide torque values by 3.              

Time for

1 turn

(sec)

OFF

OFF

23

OFF

ON

11

ON

OFF

7

ON

ON

4

24VDC

60

24VDC

115

24VDC

145

66% Power*

100% Power*

Torque in in-lbs

Torque in in-lbs

Torque in in-lbs

DIP 1

DIP 2

33% Power*

16% Power*

Torque in in-lbs

24VDC

35

 

 

 

 

 

 

 

 

To convert in-lbs to Nm, divide the in-lbs value by 9

 

 

 

Speed and Torque of MC

H

-xxxAx Actuators (Not battery fail-safe) 

Time for

1 turn

(sec)

OFF

OFF

90

OFF

ON

45

ON

OFF

30

ON

ON

18

24VDC

205

24VDC

400

24VDC

497

24VDC

120

DIP 1

DIP 2

Torque in in-lbs

Torque in in-lbs

Torque in in-lbs

Torque in in-lbs

16% Power*

33% Power*

66% Power*

100% Power*

 

   

 

 

 

 

 

 

To convert in-lbs to Nm, divide the in-lbs value by 9

 

 

Speed and Torque of MC

F

-B-xxxAx Actuators 

Time for

1 turn

(sec)

OFF

OFF

161

OFF

ON

77

ON

OFF

49

ON

ON

28

24VDC

1241

24VDC

756

24VDC

1008

24VDC

1134

DIP 1

DIP 2

Torque in in-lbs

Torque in in-lbs

Torque in in-lbs

Torque in in-lbs

16% Power*

33% Power*

66% Power*

100% Power*

 

 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Note: 66% setting and 100% setting require voltage supply minimum values as follows:  

-

 

Supply voltage needs to be min 24vDC for battery fail-safe models. 

-

 

When operating above 20VDC and 66% power, Duty cycle is reduced to 50% - 25% maximum. 
At these levels, the electronics produce more heat which must be dissipated (depending on 
environmental temperature)  

 

Note: Digital potentiometer functionality is disabled for supply voltages below 18VDC, so the 
actuator position will not be retained on power-loss, on power-up the actuator will need to be 
re-zeroed every time.   For the battery fail-safe model, upon loss of power, the actuator will 
move to the defined fail position and track the movement. 
Battery fail-safe models will not operate below 18vDC  

Operating torque is 100%.  These torque values are for valve seating. 

 

Operating torque is 100%.  These torque values are for valve seating. 

 

Содержание MC-B-A-8.09 Series











Отзывы: