Hamworthy UF150-1, Инструкция по установке, вводу в эксплуатацию и эксплуатации

Страница: 7 / 64

HAMWORTHY HEATING LTD
1
UPTON FLOOR STANDING SERIES 500001340/C
1.0 INTRODUCTION
1.1 This boiler must be installed by a competent person. Please read the technical and user instructions before installing
and lighting the boiler. All installations MUST conform to the relevant Gas Safety and Building Regulations. Health &
Safety requirements must also be taken into account when installing any equipment. Failure to comply with the above
may lead to prosecution.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions
concerning cleaning, maintenance and use of the appliance by a person responsible for their safety. Children
should be supervised to ensure that they do not play with the appliance.
1.2 This boiler is intended for use on Group H Natural Gas (2nd Family) I
2H
or LPG Propane (3rd Family) I
3P
.The firing
information is to be found in Appendix ‘A’. Boilers MUST NOT use gas other than that for which they are designed and
adjusted.
1.3 The Upton is a gas fired, fully modulating, condensing, fan assisted, open flued central heating / hot water boiler. Using
the latest gas / air ratio control technology it is able to provide clean efficient operation across a large output range.
1.3.1 The boiler can be supplied in a modular format, a maximum of three vertically stacked modules being arranged into
a single unit sharing a common flue.
1.3.2 Each boiler module utilises a metal fibre, fan assisted, pre - mix burner.
1.3.3 Operation is initiated and controlled by a Navistem boiler management system with a user interface LCD display for
accessing and changing boiler parameters.
1.3.4 Each of the boiler models is designed for direct connection to a flue system. The Technical Data is given in
Appendix ‘C’
. The flue outlets from more than one unit may be connected to a single chimney.
No draught diverter is fitted to the boiler nor is a fixed diverter required in the flue system. However a draught stabiliser
may be required for some installations.
1.3.5 The Upton is floor mounted and is intended for the heating of Commercial and Industrial premises.
It may also be used to supply hot water for these premises via an indirect cylinder.
1.3.6 The Upton has a low water content and water flow rates MUST be maintained at or above the recommended levels
shown in Appendix ’E’.
1.4 This boiler must be connected an un - vented (pressurised) heating system, it must not be used on open vented
systems. Care must be taken to ensure all extra safety requirements are satisfied and that the relevant interlocks will shut
the boiler(s) off should a high or low pressure fault occur.
1.4.1 The pressurisation unit must also incorporate a low level water switch which protects the water pumps and will
directly or indirectly shut down the boiler plant should a low water condition occur.
1.4.2 Consideration should also be given to the maximum working pressure of the boiler as given in Appendix ’E’.
Consult Hamworthy Heating Technical Department for help or assistance if in doubt.
1.5 The Upton boiler is not suitable for direct connection to domestic hot water supplies.
1.6 The Upton boiler can be installed with reverse return water flow, (optional HHL pipe kits are available, complete with
individual shut pumps and low loss header for up to 12 modules in two or three vertically stacked units). See Appendix ‘E’,
figure E1.1 for typical schematic layouts
1.7 Regulatory disposal and managed recycling of this product can prevent damage to the environment and
health risks.
a) For the disposal of the product and the component parts, the services of an accredited waste disposal
company should be used.
b) For more information on waste disposal/management, contact the Local Authority responsible for waste
management or the point of sales where the product was purchased.