background image

Here are some suggestions to help you 
maintain your fan

1.Because of the fan's natural movement, 
some connections may become loose.  

Check 

the support connections, brackets, and blade 
attachments twice a year.

  Make sure they are 

secure.  

(It is not necessary to remove fan 

from ceiling.)

2. Clean your fan periodically to help maintain 
its new appearance over the years.  Use only a 
soft brush or lint-free cloth to avoid scratching 
the finish.  The plating is sealed with a 
l a c q u e r   t o  m i n i m i z e   d i s c o l o r a t i o n  o r  
tarnishing.  Do not use water when cleaning.  
This could damage the motor, or the wood, or 
possibly cause an electrical shock.

3. You can apply a light coat of furniture polish to 
the wood blades for additional protection and 
enhanced beauty.  Cover small scratches with a 
light application of shoe polish.

4. 

There is no need to oil your fan. 

 The motor 

has permanently lubricated bearings.

11. Care of Your Fan 

IMPORTANT

MAKE SURE THE POWER IS OFF AT THE 

ELECTRICAL PANEL BOX BEFORE YOU 

ATTEMPT ANY REPAIRS.  REFER TO THE 

SECTION "MAKING ELECTRICAL 

CONNECTIONS"

Содержание Waterton II

















Отзывы: