background image

Questions, problems, missing parts? Before returning to the store,

call Hampton Bay Customer Service

8 a.m. – 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday 

 

 

1-855-HD-HAMPTON

HAMPTONBAY.COM

Retain this manual for future use.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause 
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING:

 Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's 

authority to operate the equipment.

NOTE:

 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, 
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference 
to radio communications. 

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference 
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

Содержание LOOMIS YG990-MBK


















Отзывы: