manualshive.com logo in svg

HAMPTON BAY H27-NG, Инструкция для владельца и по установке

Поделиться
Скачать
HAMPTON BAY H27-NG Скачать руководство пользователя страница 1

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD.  6988 Venture St., Delta, BC  Canada, V4G 1H4

918-812

MODELS:      H27-NG Natural Gas       H27-LP Propane   

04/12/11

H27 Direct Vent Gas Fireplace

Owners & 

Installation Manual

WARNING:  
If the information in these instructions are not 
followed exactly, a fi re or explosion may result 
causing property damage, personal injury or loss 
of life. 

FOR YOUR SAFETY
Do not store or use gasoline or other fl ammable 
vapours and liquids in the vicinity of this or any 
other appliance.

Installation and service must be performed by 
a qualifi ed installer, service agency or the gas 
supplier.

FOR YOUR SAFETY

What to do if you smell gas:
  Do not try to light any appliance
  Do not touch any electrical switch: 

do not use any phone in your 
building.

  Immediately call your gas supplier 

from a neighbour's phone. Follow 
the gas supplier's instructions.

  If you cannot reach your gas sup-

plier, call the fi re department.

This appliance may only be 
installed in an aftermarket 
permanently located, manu-
factured (USA only) or mobile 
home, where not prohibited by 
local codes.

This appliance is only for use 
with the type of gas indicated 
on the rating plate. This ap-
pliance is not convertible for 
use with other gases, unless 
a certifi ed kit is used.

Tested by:

Installer: Please complete the details on the back cover 

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

www.hampton-fi re.com

Содержание H27-NG

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды