background image

8

Assembly - Close-To-Ceiling Mount

Assembly - Hanging the Fan

Attaching the fan to the electrical 
box

 

Pass the 120-Volt supply wires through the center hole in the 
mounting bracket (A).

 

Install the ceiling mounting bracket on the outlet box by sliding 
the mounting bracket (A) over the two screws (II) provided with 
the outlet box. If necessary, use leveling washers (not included) 
between the mounting bracket (A) and the outlet box. Note that 
the flat side of the mounting bracket (A) is toward the outlet box. 
When using close-to-ceiling mounting, it is important that the 
mounting bracket be level.

 

Securely tighten the two mounting screws (II).

1

WARNING:

 To reduce the risk of fire, electric shock or personal 

injury, mount to outlet box marked “Acceptable for fan support 

of 35 lbs. (15.9 Kg) or less”, and use screws provided with the 

outlet box.

A

II

II

Preparing for mounting

Routing the wires

1

2

 

Remove canopy ring (D) from the canopy (C) by turning the 
ring counter-clockwise until it unlocks. 

 

Remove the mounting bracket (A) from the canopy (C) by 
loosening the two canopy screws (FF) located in the “L 
shaped” slots.

 

Remove and save the two canopy screws (FF) and lock 
washers (GG) in the round holes. This will enable you to 
remove the mounting bracket (A).

 

Remove the decorative canopy bottom cover (M) from the 
canopy (C) by pressing the three studs located inside the 
bottom of the canopy.

 

Remove three of the six screws (JJ) and lock washers (KK)   
(every other one) securing the motor collar to the top of the  
fan motor housing (F). 

 

Place the rubber gasket (AA) over the remaining three 
screws, and route the wires exiting the top of the fan motor 
(F) through the canopy ring (D). Make sure the slot opening is 
on top, then proceed to place the ceiling canopy (C) over the 
collar at the top of the motor (F). 

 

Align the mounting holes with the holes in the motor (F) and 
fasten, using the three screws (JJ) and lock washers (KK) 
removed previously. Tighten the mounting screws securely.

A

C

D

GG

M

FF

C

AA

D

KK

JJ

Содержание DEVRON 57231


















Отзывы: