background image

EXCELDirect

®

 

DIRECT VENT VENTING SYSTEM 

INSTALLATION AND MAINTENANCE INSTRUCTIONS

 

 

EXCELDirect

®

  is  a  certified  venting  system  designed  to  be  used  only  with  certified 

direct vent gas fired appliances. 

 

The  direct  vent  gas  appliance  must  be  certified  for  use  with  the  ICC  EXCELDirect

®

 

venting system. Refer to the manufacturer's labeling and instruction manual to confirm 
that EXCELDirect

®

 is listed for use with the appliance model you have selected. 

ARNING 

WARNING 

  The installation must conform with local codes or, in the absence of local codes, 

with the following code in force: 

 

- National Fuel Gas Code, ANSI Z223.1 (USA) or, 

 

- Natural Gas and Propane Installation Code, CAN/CSA B149.1 (Canada). 

  A major cause of vent related fires is failure to maintain required clearances (air 

space)  to  combustible  materials.  The  venting  configurations  and  clearances 
requirements are indicated in the Direct Vent gas appliance instructions manual. 
It  is  of  utmost  importance  that  this  venting  system  be  installed  only  in 
accordance  with  these  instructions.  Do  not  fill  the  air  space  with  insulating 
material.

 

  A direct vent appliance must be connected to a single venting system. Multiple 

venting is not allowed. 

  Specific requirements for horizontal installation, such as minimum clearances to 

balcony, window, door, soffit, etc. are detailed in this manual. 

  Contact local building or fire officials about restrictions and installation inspection 

in your area. 

S

 

Do not begin installing the ICC EXCELDirect

®

 venting system until you have carefully 

read the appliance and vent system installation instructions.  

 

Use  only  ICC  model  EXCELDirect

®

  components.  Failure  to  do  so  will  void  the 

certification and warranty of the product. 

 

Keep  these  installation  and  operating  instructions  in  a  safe  location  for  future 
reference. 

 

EXCELDirect

®

 has been tested and listed to the following: 

.  UL 2112 Standard by Underwriters Laboratories inc. (Listing #MH300439) 
.  Conforms to ANSI Z21 Std for Direct vent gas appliances and UL Std 2112 

by INTERTEK.  (ETL Listing # 4005717) 

.  Certified to CSA Std for Direct vent gas appliances by INTERTEK. 
 

(ETL Listing # 4005717) 

 

 

 

 

 

ICC INDUSTRIAL CHIMNEY COMPANY INC. 

400 J.F. Kennedy, St. Jerome 

Quebec, Canada, J7Y 4B7 

Tel.: (450) 565-6336, Fax: (450) 565-65 19 

www.icc-rsf.com

 

 

XLT-II_2019-05

 

Summary of Contents for EXCELDirect























Reviews: