background image

Problem

Fan will not start.

Fan sounds noisy.

Remote control 
malfunction:

Solution

1.Check circuit fuses or breakers.

2. Check line wire connections to the fan and switch wire connections in the switch housing.
    

CAUTION

: Make sure main power is off.

3. Check to make sure the dip switches from the transmitter and receiver are set to the same frequency.

1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade bracket to the motor hub is tight.

3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing.
    

CAUTION

: Make sure main power is off.

4. Allow a 24-hour "breaking-in" period.  Most noise associated with a new fan disappear during this time.

5. If using an optional light kit, make sure the screws securing the glassware are tight.  Check that 

light bulb 

is also secure.

6. 

7. Make sure the upper canopy is a short distance from the ceiling. 

 It should not touch the ceiling.

the 

Do not connect the fan with a wall  mounted variable speed control (s)

1. Do not connect the fan with a wall  mounted variable speed control (s)

2. Make sure the dip switches are set correctly.

Troubleshooting 14. 

Содержание 460-922


















Отзывы: