Hammerhead 2013 R 150 Скачать руководство пользователя страница 9

Страница: 9 / 100

SAFETY

Safe Riding Gear

Helmet

Wearing a helmet can prevent a severe head injury. Whenever riding this

HAMMERHEAD vehicle, always wear a helmet that meets or exceeds

established safety standards.
Approved helmets in the USA and Canada bear a U.S. Department of

Transportation (DOT) label.
Approved helmets in Europe, Asia and Oceania

bear the ECE 22.05 label. The ECE mark consists

of a circle surrounding the letter E, followed by the

distinguishing number of the country which has

granted approval. The approval number and serial

number will also be displayed on the label.

Eye Protection

Do not depend on eyeglasses or sunglasses for eye protection.

Whenever riding this HAMMERHEAD vehicle, always wear

shatterproof goggles or use a shatterproof helmet face shield.

HAMMERHEAD recommends wearing approved Personal Protective

Equipment (PPE) bearing markings such as VESC 8, V-8, Z87.1, or CE.

Make sure protective eye wear is kept clean.

Gloves

Wear gloves for comfort and for protection from sun, cold weather and

other elements.

Boots

Wear sturdy over-the-ankle boots for support and protection. Never ride

a HAMMERHEAD vehicle with bare feet or sandals.

Clothing

Wear long sleeves and long pants to protect arms and legs.

Rider Comfort

Under certain operating conditions, heat generated by the engine and

exhaust system can elevate temperatures in the driver and passenger cab

area. The condition occurs most frequently when a vehicle is being

operated in high ambient temperatures at low speeds and/or high load

conditions for an extended period of time. The use of certain

windshield, roof and/or cab systems may contribute to this condition by

restricting airflow. Any discomfort due to heat buildup in this area can

be minimized by wearing proper riding apparel and by varying speeds to

increase airflow.

051039

0006.31

Содержание 2013 R 150





































































































Результаты поиска

Содержание 2013 R 150

Отзывы:

Похожие инструкции для 2013 R 150

Бренды по названию

Популярные бренды

Hammerhead 2013 R 150, Руководство пользователя

Результаты поиска

Содержание 2013 R 150

Отзывы:

Похожие инструкции для 2013 R 150

Бренды по названию

Популярные бренды