manualshive.com logo in svg

Hammerhead 2013 R 150, Руководство пользователя

Поделиться
Скачать
Hammerhead 2013 R 150 Скачать руководство пользователя страница 64

64

MAINTENANCE

Toe Alignment

Use the following procedure to check the toe alignment of the vehicle. 

The recommended toe alignment is 1/8” to 1/4” (3-6 mm) toe out.

WARNING!

Severe injury or death can result from improper toe alignment and 

adjustment. Do not attempt to adjust tie rod alignment. All tie rod adjustments 

should be performed by an authorized HAMMERHEAD dealer or other qualified 

service facility.

1. Position the vehicle on a 

level surface.

2. Set the steering wheel in a 

straight-ahead position and 

secure them in this position.

3. Place a chalk mark on the 

center line of the front tires 

as close to the hub/axle 

center line as possible. Make 

sure both marks are the same 

distance from the floor.

4. Measure the distance between the marks and record the 

measurement.

5. Move the vehicle to rotate the tires 180°. Position the wheels with 

the chalk marks at the rear of the tires, even with the hub/axle center 

line.

6. Measure the distance between the marks and record the 

measurement.

7. Subtract the front dotted line from the back dotted line. The 

difference is the vehicle toe-out alignment.

8. If you discover improper alignment, your preferred dealer can 

assist.

Содержание 2013 R 150





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды