manualshive.com logo in svg

Hammer HNC3 825, Перевод оригинальной инструкции по эксплуатации

Поделиться
Скачать
Hammer HNC3 825 Скачать руководство пользователя страница 63

63

HNC3 825 / HNC3 825 perform

Maintenance

1

Fig. 46: Lubricating nipple Y-axis ball screw drive

Personnel:

●

Trained machine operator

Protective equipment:

●

Protective clothing

●

Protective gloves

●

Protective footwear

●

Safety goggles

Tool:

●

Grease gun

●

Cleaning cloths

Material:

●

Lubricant Interflon Grease HD2

Interval: Every 60 operating hours or if irregular noise occurs.

1.

Switch off the machine at the main switch, disconnect the power supply.

2.

Remove visible dirt or grease.

3.

Clean lubricating nipple.

4.

Place the pressure grease gun onto the nipple and pump 3 times.

🡆

A small amount of lubrication will come out of the seals.

5.

Switch machine on.

6.

Move several times over the entire length of the axle to distribute the grease.

🡆

Axis is covered with a thin film of grease.

Y Axis: Lubricate guiding carriage

On the side of the portal there are two lubricating nipples for each of the Y axis

guides.

Содержание HNC3 825

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды