Hamilton Engineering EVO Plus Series Скачать руководство пользователя страница 18

Страница: 18 / 64

PART 4. VENTING

PART 4. VENTING

A. APPROVED VENTING MATERIALS

ALL VENT PIPE MATERIALS AND FITTINGS MUST COMPLY WITH THE FOLLOWING:

Item

Material

Standards for installation in:

United States

Canada

Vent pipe

and

fittings

AL 29-4C Stainless

ANSI/ASTM UL1738

UL1738

PVC schedule 40*

ANSI/ASTM D1785

CPVC and PVC venting must be ULC-S636

Certified. IPEX is an approved vent

manufacturer in Canada supplying vent

material listed to ULC-S636.

CPVC schedule 40

ANSI/ASTM F441

Polypropylene

ULC-S636

Pipe cement

& primer

PVC

ANSI/ASTM D2564

IPEX System 636

Cements & Primers

CPVC

ANSI/ASTM F493

NOTICE: DO NOT USE CELLULAR (FOAM) CORE PIPE

Please note: Venting system may contain one or more of the above materials.

The EVO is a direct vent appliance. The EVO is listed as a Category IV condensing appliance. (The EVO

Venting is rated at Zero Clearance to combustibles.)

THE EVO EFFICIENCY TESTING AND RATINGS ARE BASED ON A SEALED, TWO PIPE

VENT SYSTEM; HOWEVER, MANY OTHER VENT CONFIGURATIONS ARE AVAILABLE AS

FACTORY ENGINEERED SOLUTIONS. PLEASE CONTACT THE FACTORY IF EXCEPTIONS

ARE REQUIRED FOR YOUR INSTALLATION.

SPECIAL VENTING SYSTEM DESIGN NOTES

It is extremely important to follow these

venting instructions carefully. Failure to do

so can cause severe personal injury, death

or substantial property damage.

This vent system will operate with a positive

pressure in the vent pipe. Do not connect

vent connectors serving appliances by

natural draft into any portion of mechanical

draft systems operating under pressure.

DANGER

WARNING

NOTE:

For concrete construction or to meet certain fire codes, exhaust and inlet piping at the wall penetration to the

EVO must be CPVC Schedule 40 or 80 or stainless. The balance from the penetrated wall to the outside may be PVC

Schedule 40 or 80.

NOTE: If set points exceed 140ºF, use of PVC is NOT recommended, even though product is approved as such.

Contact Hamilton Engineering at 800.968.5530 for further clarification.

Содержание EVO Plus Series

































































Результаты поиска

Содержание EVO Plus Series

Отзывы:

Похожие инструкции для EVO Plus Series

Бренды по названию

Популярные бренды

Hamilton Engineering EVO Plus Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание EVO Plus Series

Отзывы:

Похожие инструкции для EVO Plus Series

Бренды по названию

Популярные бренды