2
G
Operating instruction
Thank you for choosing a Hama product.
Take your time and read the following instructions and information completely. Please keep
these instructions in a safe place for future reference. If you sell the device, please pass
these operating instructions on to the new owner.
1. Explanation of Warning Symbols and Notes
Warning
This symbol is used to indicate safety instructions or to draw your attention to
specific hazards and risks.
Note
This symbol is used to indicate additional information or important notes.
2. Package Contents
•
PG-300
DCF wireless wall clock
•
1 AA battery
•
These operating instructions
3. Safety Notes
•
The product is intended for private, non-commercial use only.
•
Use the product for its intended purpose only.
•
Protect the product from dirt, moisture and overheating, and only use it in a dry
environment.
•
Do not use the product in the immediate vicinity of heaters or other heat sources or in
direct sunlight.
•
Do not operate the product continuously, as it is not designed for this.
•
Do not drop the product and do not expose it to any major shocks.
•
Do not attempt to service or repair the product yourself. Leave any and all service work
to qualified experts.
•
Do not put the product near interference fields, metal frames, computers, TVs, etc.
Electronic devices and window frames can negatively affect the product’s functionality.
•
Do not modify the product in any way. Doing so voids the warranty.
•
Keep the packaging material out of the reach of children due to the risk of suffocation.
•
Dispose of packaging material immediately according to locally applicable regulations.
Warning – Batteries
•
When inserting batteries, note the correct polarity (+ and - markings) and insert
the batteries accordingly. Failure to do so could result in the batteries leaking or
exploding.
•
Only use batteries (or rechargeable batteries) that match the specified type.
•
Before you insert the batteries, clean the battery contacts and the polar contacts.
•
Do not allow children to change batteries without supervision.
•
Do not mix old and new batteries or batteries of a different type or make.
•
Remove the batteries from products that are not being used for an extended period
(unless these are being kept ready for an emergency).
•
Do not short-circuit batteries.
•
Do not charge batteries.
•
Do not throw batteries in a fire.
•
Keep batteries out of the reach of children.
•
Never open, damage or swallow batteries or allow them to enter the environment.
They can contain toxic, environmentally harmful heavy metals.
•
Immediately remove and dispose of dead batteries from the product.
•
Avoid storing, charging or using batteries in extreme temperatures.
4. Getting Started
4.1 Inserting the battery
•
Remove the battery that was already inserted; remove the protective film if necessary
as well as the contact interrupter, and then re-insert the battery with the correct
polarity. The clock is ready for operation.
4.2 Replacing the battery
•
Remove and dispose of any used batteries. Insert a new battery (AA). Ensure that
the polarity of the battery corresponds to the symbols in the battery compartment.
5. Installation
•
You can mount the PG 300 DCF wireless wall clock on a wall using the opening
on the back.
Warning – Mounting Note
•
Before mounting the clock, ensure that the chosen wall is suitable for
the weight to be mounted, and make sure that there are no electrical
wires, water, gas or other lines at the installation site on the wall.
•
Purchase special fastening materials from specialised dealers.
•
Do not mount the product above locations where persons might linger.
6. Operation
6.1 Automatic time setting
•
Once the battery is inserted properly, the clock will automatically be set to 12:00 pm and
its reception will be activated. As soon as the DCF signal was received and processed
(approx. 3 to 15 minutes), the correct time is displayed automatically. Do not move the
clock during this process.
•
If the clock has not correctly set itself after 15 minutes, there is a problem with the
reception or with the selected location.
•
Repeat the setting process at another location. First, remove the battery for about 1
minute and then insert it in the battery compartment again.
6.2 Setting the time manually
M.SET button:
•
Hold down the M.SET button until the appropriate time appears.
•
As soon as the clock receives the DCF signal, it will reset the time.
REC button:
•
Press and hold the REC button on the rear side for 3 seconds. The seconds hand moves
to the 12 position. It then tries to receive the time signal and reset itself accordingly.
•
If the clock finds a DCF signal, it adjusts itself automatically. If no signal is received
within 16 minutes, the clock reverts to the original time.
RESET button:
•
Press and hold the RESET button on the rear side for 3 seconds. The clock sets itself to
position 12. It then tries to receive the time signal and reset itself accordingly.
Note
Note that electronic devices such as TVs, PCs, etc. can interfere with reception
when located within up to two metres of the product.
7. Care and Maintenance
Only clean this product with a slightly damp, lint-free cloth and do not use aggressive
cleaning agents. Make sure that water does not get into the product.
8. Warranty Disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting
from improper installation/mounting, improper use of the product or from failure to
observe the operating instructions and/or safety notes.
9. Technical Data
PG-300 DCF wireless wall clock
Power supply
1.5 V
1 AA battery
10. Declaration of Conformity
Hereby, Hama GmbH & Co KG declares that the radio equipment type
[00186359, 00136219, 00136220, 00136221] is in compliance with
Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at the following internet address:
www.hama.com->00186359, 00136219, 00136220, 00136221->Downloads.
Frequency band(s)
77.5 kHz
