2
G
Operating instruction
Controls and Displays
1.
AM/PM (12-hour format)
2.
Time
3.
Day
4.
Month
5.
Day of the week
6.
Moon phase
7.
Room temperature
8.
Time zone
9.
Summer time
10. Battery symbol
11. Wireless symbol
12. Opening for wall mounting
13. Base
14.
MODE
button
= settings/confirms the setting
15.
°F/°C
button
= switches between °C and °F
16.
UP
button
= increases the current setting; activates/deactivates manual radio signal
reception; switches the display mode
17.
DOWN
button
= decreases the current setting; activates/deactivates manual radio signal
reception; selects the language
18. Battery compartment
Thank you for choosing a Hama product.
Take your time and read the following instructions and information completely.
Please keep these instructions in a safe place for future reference. If you sell the
device, please pass these operating instructions on to the new owner.
1. Explanation of Warning Symbols and Notes
Warning
This symbol is used to indicate safety instructions or to draw your attention to
specific hazards and risks.
Note
This symbol is used to indicate additional information or important notes.
2. Package Contents
•
PP-245 DCF wireless wall clock
•
1 AA battery
•
These operating instructions
3. Safety Instructions
•
The product is intended for private, non-commercial use only.
•
Do not operate the product outside the power limits given in the specifications.
•
Do not use the product in moist environments and avoid splashes.
•
Do not use the product in the immediate vicinity of heaters or other heat sources
or in direct sunlight.
•
Do not use the product in areas where the use of electronic devices is not permitted.
•
Do not place the product near interference fields, metal frames, computers, TVs,
etc. Electronic devices and window frames can negatively affect the product’s
functionality.
•
Do not drop the product and do not expose it to any major shocksl.
•
Do not open the device or continue to operate it if it becomes damaged.
•
Do not attempt to service or repair the product yourself. Leave any and all service
work to qualified experts.
•
Keep the packaging material out of the reach of children due to the risk of
suffocation.
•
Dispose of packaging material immediately according to locally applicable
regulations.
•
Do not modify the product in any way. Doing so voids the warranty.
Warning – Batteries
•
Immediately remove and dispose of dead batteries from the product.
•
Only use batteries (or rechargeable batteries) that match the specified type.
•
Do not mix old and new batteries or batteries of a different type or make.
•
When inserting batteries, note the correct polarity (+ and - markings) and
insert the batteries accordingly. Failure to do so could result in the batteries
leaking or exploding.
•
Do not overcharge batteries.
•
Keep batteries out of the reach of children.
•
Do not short circuit the batteries/rechargeable batteries and keep them away
from uncoated metal objects.
4. Getting Started
4.1 Inserting the battery
Remove the battery that was already inserted into the clock, remove the protective
film if necessary as well as the contact interrupter and the re-insert the battery with
the correct polarity. The clock is ready for operation.
4.2 Replacing the battery
Remove and dispose of any used batteries. Insert the new battery (AA). Ensure that
the polarity of the battery corresponds to the symbols in the battery compartment
(18).
5. Installation
•
You can mount the wall clock on a wall using the opening on the back (12).
Warning – Mounting Note:
•
Before mounting the clock, ensure that the chosen wall is suitable for the
weight to be mounted, and make sure that there are no electrical wires,
water, gas or other lines at the installation site on the wall.
•
Purchase special fastening materials from specialised dealers.
•
You can also stand the wall clock on a level surface using the base (13).
6. Operation
Note – Input
Hold down the
UP
button (16) or the
DOWN
button (17) to select the values
faster.
6.1. Automatic setting using the DCF signal
•
Once the batteries are inserted, the clock automatically searches for a DCF signal.
During the search, the wireless icon (11) flashes.
Display
Searching for the DCF signal
Display flashing
Active
Displayed continuously
Successful – signal is being
received
Not displayed
Deactivated
•
If the station still does not receive a signal, press and hold the UP button (16) and
the DOWN button (17) for approx. 3 seconds to start the manual search for the
DCF signal. The wireless icon (11) will start to flash.
