14
15
WB1
Size
86mm x 77mm x 28mm / 3.39” x 3.03” x 1.10”
Sensor Compatibility**
Bosch LSU 4.9 or NTK LZA08-H5
Supply Voltage
6.5V to 16V DC, Short circuit,reverse polarity protection
Supply Current
650mA Typical / 4A Peak
Maximum Temperature
85C (185F)
Communications
CAN (Haltech) with baud rate of 1Mbit/sec
Configuration
Haltech NSP Software, ESP Software, or ECU Manager
CAN Connection
2 x DTM-4 Connectors / 1 x DTM04-6P Connection
PRODUCT SPECIFICATIONS
WB2
Size
86mm x 77mm x 28mm / 3.39” x 3.03” x 1.10”
Sensor Compatibility**
Bosch LSU 4.9 or NTK LZA08-H5
Supply Voltage
6.5V to 16V DC, Short circuit,reverse polarity protection
Supply Current
1.3A Typical / 8A Peak
Maximum Temperature
85C (185F)
Communications
CAN (Haltech) with baud rate of 1Mbit/sec
Configuration
Haltech NSP Software, ESP Software or ECU Manager
CAN Connection
2 x DTM-4 Connectors / 2 x DTM04-6P Connection
** Sensors are compatible with specific WB1/WB2 Controllers. ie. NTK WB1 only compatible with NTK sensor.
At Haltech we make every effort to design and manufacture fault-
free products that perform up to or above the market expectations.
All our products are covered by a Limited 12 Month Warranty.
Haltech Limited Warranty
Unless specified otherwise, Haltech warrants its products to be free from
defects in material or workmanship for a period of 12 months from the
date of purchase.
If the Haltech product is found to be defective as mentioned above, it will be
replaced or repaired if returned prepaid along with proof of purchase. Proof
of purchase in the form of a copy of the original purchase invoice, receipt
or bill of sale which indicates that the product is within the warranty period,
must be presented to obtain warranty service.
Replacement or repair of a defective product shall constitute the sole lia-
bility of Haltech. To the extent permitted by law, the foregoing is exclusive
and in lieu of all other warranties or representations, either expressed or
implied, including any implied warranty of merchantability or fitness. In no
event shall Haltech, be liable for special or consequential damages.
Product Returns
Please include a copy of the original purchase invoice, receipt or bill of sale
along with the unused, undamaged product and its original packaging. Any
product returned with missing accessory items or packaging will incur extra
charges to return the item to a re-saleable condition.
All product returns must be sent via a freight method with adequate track-
ing, insurance and proof of delivery services. Haltech will not be held re-
sponsible for product returns lost during transit.
Returns of Products Supplied in Sealed Packaging
The sale of any sensor or accessory supplied in sealed packaging is strictly
non-refundable if the sealed packaging has been opened or tampered with.
This will be clearly noted on the product packaging. If you do not accept
these terms please return the sensor in its original unopened packaging
within 30 days for a full refund.
A sensor or accessory product may be returned after 30 days of purchase
(with its sealed packaging in tact) for credit only (no refunds given) and will
be subject to a 10% restocking fee.
Installation of Haltech Products
No responsibility whatsoever is accepted by Haltech for the fitment of
Haltech Products. The onus is clearly on the installer to ensure that both
their knowledge and the parts selected are correct for that particular appli-
cation. Any damage to parts or consequential damage or costs resulting
from the incorrect installation of Haltech products are totally the respon-
sibility of the installer.
Always disconnect the battery when doing electrical work on your vehicle.
Avoid sparks, open flames or use of electrical devices near flammable sub
-
stances. Do not run the engine with a battery charger connected as this
could damage the ECU and other electrical equipment.
Do not overcharge the battery or reverse the polarity of the battery or any
charging unit. Disconnect the Haltech ECU from the electrical system
whenever doing any welding on the vehicle by unplugging the wiring har-
ness connector from the ECU.
After completing the ECU installation, make sure there is no wiring left
un-insulated. Uninsulated wiring can cause sparks, short circuits and in
some cases fire. Before attempting to run the engine ensure there are no
leaks in the fuel system. All fuel system components and wiring should be
mounted away from heat sources, shielded if necessary and well ventilat-
ed. Always ensure that you follow workshop safety procedures. If you’re
working underneath a jacked-up car, always use safety stands!
__________________________________________________________
Haltech Off-Road Usage Policy
In many states it is unlawful to tamper with your vehicle’s emissions equip-
ment. Haltech products are designed and sold for sanctioned off-road/com
-
petition non-emissions controlled vehicles only and may never be used on
a public road or highway.
Using Haltech products for street/road use on public roads or highways is
prohibited by law unless a specific regulatory exemption exists (more infor
-
mation can be found on the SEMA Action Network website www.semasan.
com/emissions for state by state details in the USA).
It is the responsibility of the installer and/or user of this product to ensure
compliance with all applicable local and federal laws and regulations.
Please check with your local vehicle authority before purchasing, using or
installing any Haltech product.
WARRANTY CERTIFICATE