Halstead Ace High Скачать руководство пользователя страница 23

Страница: 23 / 40

ROUTINE SERVICING

LOCATION OF
SERVICEABLE
COMPONENTS

6.1

MAIN BURNER ASSEMBLY

6.2

BURNER INJECTOR

6.3

IGNITION AND DETECTION ELECTRODES

To ensure continued efficient operation of the appliance, it is

recommended that it is checked and serviced as necessary at

regular intervals. The frequency of servicing will depend upon the

particular installation conditions and usage but in general once a

year should be adequate. It is the law that any service work must

be carried out by a competent person, such as British Gas or

other CORGI registered personnel.
The boiler incorporates a flue sampling point on the top panel in

front of the flue outlet. If the service engineer has suitable

equipment to analyse the flue gas, the plastic cap may be

removed and a 6mm inside diameter sample tube fitted. Do not

forget to replace the plastic cap after use.
Before commencing any service operation, ISOLATE the mains

electrical supply, and TURN OFF the gas supply at the main

service cock.
Service the appliance by following the full procedure detailed

below:

Remove the casing front panel by unscrewing the panel

retaining screw and lifting off the panel.

Remove the sealed chamber front panel (4 screws).

Remove the combustion chamber front panel (7 screws). Take

care not to damage the insulation.

Do not attempt to light the burner with Front Panel
removed.

Remove the 4 screws securing the burner on the gas manifold.

Unscrew and remove the two screws securing the control

panel in the upright position and pivot the panel forwards.

Remove the two spark and one detection electrode leads from

the electrodes.

Check that the injectors fitted in the gas manifold are free from dirt

and debris. If necessary clean the injector orifice carefully using a

soft brush or vacuum cleaner. Do not use a wire brush or any

abrasive material.

It is not necessary to remove the injectors.

If there are

signs of injector(s) being blocked please call the Halstead Service

Department.

Inspect the ignition and detection electrodes in situ. If

necessary clean using a soft brush. If either the electrode or

the ceramic insulation show signs of damage or wear, replace

the electrode(s).

Check that the alignment of the ignition and detection

electrodes are as shown in Figure 34. Adjust by carefully

bending the tip of the electrode rod whilst supporting the base

of the rod. Do not put any pressure on the ceramic insulation.

Remove the burner by lifting it forward with reference to

Figure 33.

Inspect and if necessary clean the main burner ports using a

soft brush or vacuum cleaner. Do not use a wire brush or any

abrasive material.

•

COMBUSTION CHAMBER
FRONT PANEL FIXING
SCREWS (7)

•

AUTO AIRVENT

FAN ASSEMBLY BASE
PLATE SCREWS

PUMP

GROUP SET

CONTROL
COVER

AIR PRESSURE
SWITCH & PIPES

DETECTION ELECTRODE

BURNER

IGNITION ELECTRODES

•

GAS CONTROL VALVE

•

PRESSURE RELIEF
VALVE

FAN ASSEMBLY

•

PRESSURE
GAUGE

•

OVERHEAT THERMOSTAT

•

CONTROL PANEL

Содержание Ace High









































Результаты поиска

Содержание Ace High

Отзывы:

Halstead Ace High, Инструкции по установке и обслуживанию, Страница: 23 / 40

Результаты поиска

Содержание Ace High

Отзывы: