Halma Ocean Optics JAZ Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 70

background image

About This Manual

013-RD000-000-02-201510

vii

WARNING

This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

FCC COMPLIANCE

This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which the user will be required to correct the interference at his on
expense.

WARNING:

The authority to operate this equipment is conditioned by the

requirement that no modifications will be made to the equipment unless the changes
or modifications are expressly approved by the manufacturer.

«
...
7
8
9
10
11
...
»

Содержание Ocean Optics JAZ







































































Отзывы:

Нет отзывов

Похожие инструкции для Ocean Optics JAZ

Бренд: Landis+Gyr Страницы: 54

Бренд: A&D Страницы: 74

Бренд: DAKOTA ULTRASONICS Страницы: 48

Бренд: TE Connectivity Страницы: 9

TEC SourceMeter 2510

Бренд: Keithley Страницы: 244

Бренд: Kawai Страницы: 112

Бренд: Parkside Страницы: 94

Бренд: PASCO Страницы: 3

Electone B-20CR

Бренд: Yamaha Страницы: 16

Бренд: YOSensi Страницы: 26

Бренд: YOSensi Страницы: 26

Бренд: Wavetronix Страницы: 14

SignalHawk SH-36S-PC

Бренд: BIRD Страницы: 137

Бренд: MICRO-EPSILON Страницы: 82

Бренд: Omicron Страницы: 76

Бренд: Galileo Страницы: 30

Litemaster Pro L-478DR

Бренд: Sekonic Страницы: 16

Бренд: M&C Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды