Halma Ocean Optics JAZ Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 70

background image

3: Operating Jaz

22

013-RD000-000-02-201510

JAZ-PX Menu

The menu for the PX light source module allows you to control the strobe and triggering functions (JAZ-
PX can operate in both free running and triggered modes), and set various parameters such as intensity
and number of flashes. This menu only appears if you have the JAZ-PX module installed in your Jaz
stack. See Chapter 4:

Operating the JAZ-PX Module

for the JAZ-PX menu and more in-depth information

on operating the JAZ-PX module.

JAZ-INDY Menu

The menu for the JAZ-INDY module allows you to configure GPIO, Analog V out, and 4-20mA
excitation and Tx control. It also lets monitor Analog and Digital inputs and calibrate voltage
inputs/outputs, and the 4-20mA transmitter/receiver. This menu only appears if you have the JAZ-INDY
module installed in your Jaz stack. See Chapter 5:

Operating the JAZ-INDY Module

for the JAZ-INDY

menu and more in-depth information on operating the JAZ-INDY module.

Storing Data on an SD Card

The JAZ-B and JAZ-E modules provide slots for up to 2 GB of storage on an SD card. The following are
procedures to ensure proper data storage on an SD card.

Note

For best results, we recommend SanDisk, Transcend and Kingston SD cards.

►

Procedure

To store data on an SD card,

1.

From the Jaz main menu, select

File System | Find SD Cards

. The Jaz screen then displays,

SD

Card Search Finished

.

2. Take your measurements. This data is continuously streamed to the SD card found in Step 1.

►

Procedure

To release an SD card,

1.

From the Jaz main menu, select

File System | Release SD Cards

. Jaz then informs you when it is

safe to remove your SD card from the slot.

2. Remove your SD card from the Jaz module to access the stored data from your computer.

«
...
30
31
32
33
34
...
»

Содержание Ocean Optics JAZ







































































Отзывы:

Нет отзывов

Похожие инструкции для Ocean Optics JAZ

Бренд: RayTek Страницы: 72

Бренд: Magnetrol Страницы: 40

Бренд: Cannon Страницы: 64

Бренд: Cannon Страницы: 73

Бренд: Ebtron Страницы: 5

Бренд: Okolab Страницы: 4

Бренд: Gazelle Страницы: 2

Бренд: OHAUS Страницы: 32

Бренд: Vanguard Instruments Company Страницы: 62

Бренд: Vanguard Instruments Company Страницы: 58

Clavinova CLP-311

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 3

Alto Horn, Baritone, Euphonium

Бренд: Yamaha Страницы: 22

Clavinova CLP-320

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 20

Бренд: Magnet-physik Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды