Halma Ocean Optics JAZ Скачать руководство пользователя страница 64

Страница: 64 / 70

A: Calibrating the Wavelength of Jaz

013-RD000-000-02-201510

7. Record the Intercept, as well as the First, Second, and Third Coefficients. Additionally, look at

the value for R squared. It should be very close to 1. If not, you have most likely assigned one of
your wavelengths incorrectly.

Keep these values at hand.

Saving the New Calibration Coefficients: USB
Mode

Ocean Optics programs wavelength calibration coefficients unique to each Jaz spectrometer module onto
an EEPROM memory chip in Jaz.

You can overwrite old calibration coefficients on the EEPROM

if you are using Jaz via the USB port.

►

Procedure

To save wavelength calibration coefficients using the USB mode, perform the following steps:

1. Ensure that Jaz is connected to the computer and that you have closed all other applications.

2. Point your browser to

http://www.oceanoptics.com/technical/softwaredownloads.asp

and

scroll down to

Microcode

. Select

USB EEPROM Programmer

3. Save the setup file to your computer.

4. Run the

Setup.exe

file to install the software. The

Welcome

screen appears.

5. Click the

Next

button. The

Destination Location

screen appears.

6. Accept the default installation location, or click the

Browse

button to specify a directory. Then,

click the

Next

button. The

Program Manager Group

screen appears.

7. Click the

Next

button. The

Start Installation

screen appears.

8. Click the

Next

button to begin the installation. Once the installation finishes, the

Installation

Complete

screen appears.

9. Click the

Finish

button and reboot the computer when prompted.

10. Navigate to the

USB EEPROM Programmer

from the Start menu and run the software.

11. Click on the desired Jaz device displayed in the left pane of the

USB Programmer

screen.

12. Double-click on each of the calibration coefficients displayed in the right pane of the USB

Programmer screen and enter the new values acquired in Steps 5 and 6 of the

Calibrating the

Wavelength of the Spectrometer

section in this appendix.

13. Repeat Step 12 for all of the new values.

14. Click on the

Save All Values

button to save the information, and then

Exit

the USB Programmer

software.

The new wavelength calibration coefficients are now loaded onto the EEPROM memory chip on the Jaz
spectrometer module

Содержание Ocean Optics JAZ







































































Результаты поиска

Содержание Ocean Optics JAZ

Отзывы:

Похожие инструкции для Ocean Optics JAZ

Бренды по названию

Популярные бренды

Halma Ocean Optics JAZ, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Ocean Optics JAZ

Отзывы:

Похожие инструкции для Ocean Optics JAZ

Бренды по названию

Популярные бренды