Halma BEA ACTIV8 THREE ON Скачать руководство пользователя страница 8

Страница: 8 / 8

8/8

Supply voltage

: 12V (– 5%) to 24V (+10%) AC/DC

Mains frequency

: 50 - 60 Hz

Power consumption

: < 3 W

Mounting height

: 1.8m to 4m

Sensitivity of the monitoring input

: 10-30V DC

Delay of the output activation after stimulation

: < 1ms

3-color LED

: RED (presence detection) – GREEN (motion detection) – ORANGE (signal saturation, error)

Temperature range

: -25°C to +55°C

Degree of protection

: IP54

Norm conformity

: R&TTE 1999/5/EC; EMC 89/336/EEC; TÜV; BS

Dimensions

: 262 mm (L) x 55 mm (H) x 44 mm (D)

Weight

: 250 g

Housing material

: ABS + LURAN S

Minimum length of cable

2.6 m

Range of Remote Control

: 5m

MOTION SENSOR

PRESENCE SENSOR

Detection mode

Motion
Minimum detection speed: 5 cm/s (measured in sensor axis)

Presence
Response time: < 128ms

Technology

Microwave and microprocessor
Transmitter frequency:

24.175 GHz

Transmitter radiated power:

< 20 dBm EIRP

Transmitter power density:

< 5 mW/cm²

Focused active infrared and self-monitored microprocessor
Spot diameter (standard): 0.1m max
Number of spots:

24 or 12 spots by curtain

Number of curtains:

Detection field

Width

Depth

Wide

4 m

2 m

Narrow

2 m

2,5 m

Width

Depth

Wide

2 m

0,35 m

Narrow

1 m

0,35 m

Angle

From 15° to 50° in elevation (adjustable)

From - 4° to + 4° (adjustable)

Output specification

Free of potential current source
State “No detection”: current source ON

Max. open circuit voltage: 6.5V
Output voltage available at 10mA: 3V min.
Typical load: up to 3 optocouplers in series

State “Detection”: current source OFF

Leakage current: <100µA
Open-circuit remained voltage: <500mV

Transistor (optocoupled transistor)

Max. output current:

100 mA

Max. switching power: 42 V DC

Output holdtime

0.5s to 9s (adjustable)

0,1/1s (fixed)

Sensing field dimensions given at 2.2m mounting height.

Specifications are subject to changes without prior notice.

Remote Control

Spotfinder

ACA

ABA

6 Technical

Specifications

7 Accessories

(sold individually)

42.

0166 /

V2 –

02.

Parc Scientifique du Sart Tilman – Allée des Noisetiers, 5 B-4031 Angleur – Belgium - TEL +32.4.3616565 - FAX +32.4.3612858 – e-mail : [email protected] - http://www.beasensors.com

Содержание BEA ACTIV8 THREE ON









Результаты поиска

Содержание BEA ACTIV8 THREE ON

Отзывы:

Похожие инструкции для BEA ACTIV8 THREE ON

Бренды по названию

Популярные бренды

Halma BEA ACTIV8 THREE ON, Руководство пользователя

Результаты поиска

Содержание BEA ACTIV8 THREE ON

Отзывы:

Похожие инструкции для BEA ACTIV8 THREE ON

Бренды по названию

Популярные бренды