background image

12

 

D-2  Setting method in AUTO/REMOVE 

mode

  Operations in REMOVE mode

This mode has the following sequence:

  Start/hot air blow (manual)

  Step 1 operation

  Step 2 operation

  Step 3 operation

  Ten seconds before the last step is 

completed, the vacuum automatically 
turns ON and then a single sound lasting 
1 second is generated. Two seconds 
before completion, a continuous sound is 
generated.

  Vacuum OFF (manual)

  Cool down 

NOTE:

The operation can be set from 1 to 50.

  Removal

  Parts mounting

Mount the nozzle and pads on the part to be 
removed. (Figure 1)

  Start (heating)

Press the HOT AIR button on the 
handpiece. Hot air blows from the 
nozzle and melts the solder. The station 
operates based on the preprogrammed 
temperature profile. (Figure 2)

CAUTION

To stop the program, press the HOT AIR 

button. Cooling begins.

  Part suction 

When the timer runs down to 10 sec., the 
vacuum automatically turns ON and the 
part is sucked. Lift the handpiece and 
remove the part from the P.W.B. (Figure 
3)

  Releasing the sucked part

To release the sucked part, press the 
VACUUM button. (Figure 3)

  Stop

After that, when the step operation is 
completed, cooling begins and the airblow 
stops as soon as the temperature reaches 
100°C (200°F). (Figure 4)

To check the set temperature, press the  

button. 

To change the set temperature, see “Setting mode in 

AUTO mode” on page 13.

In REMOVE mode, the vacuum function automatically 

turns ON during the last 10 seconds of the selected 

profile.

 CAUTION

If the vacuum button is pressed before the timer runs 

down to 10 seconds, the vacuum pump turns ON.

Press the vacuum button again to stop the air blowing.

Figure 1

Figure 2

Figure 3

Figure 4

Содержание FR-803B





























Отзывы: