Remote controlller
Wire remote controlller
Remote controlller is an accessory, to be ordered extrally
Remote controlller
Remote receiver
Installation of receive display
Because of the temperature sensitive device, do not install the receive display at straight sunlight place,
either in front of air outlet grill, for it is effected greatly from cool air and heat air, the receive display is
at least 20mm distance to the air outlet grill.
Since there is light sensitive device which receives wireless remote signal, so do not installed behind the
window curtain or other obstacles, in order not to obstruct the signal.
Must fix the remote control wire far from strong electricity (such as the wiring of electric light, air cond-
itioner, etc.) and weak electricity (such as the wiring of telephone, interphone, etc.).
2.Place the panel onto the fixed frame, pay attention
that the four claws must be placed into the
corresponding four poles on the frame
1.Fix the receive display with screws
on the selected place
C
C
1
3
4
5
2
OFF
RESET
LOCK
SLEEP
FAN
TEMP
ON
OFF
SWING
MODE
CLOCK
CODE
LIGHT
OFF
A
U
T
O
RESET
LOCK
SLEEP
FAN
TEMP
ON
OFF
SWING
MODE
CLOCK
CODE
LIGHT
OFF
A
U
T
O
CLOCK
RESET
LOCK
SLEEP
FAN
TEMP
ON
OFF
SWING
MODE
CODE
LIGHT
OFF
A
U
T
O
1
fig(1)
Left picture is a wired remote controller,
which can be used on Series wired control
units ,The remote controller can be purchased
extrally.
Wired remote Controller using method:
1.Use one wired remote controller. See fig (1)
2.Also can buy a remote controller extrally, realize
wired remote c remote control dual control modes.
3.When the remote controller can be used on series wired
remote controller units ,than please press the botton
"CODE"to choose the program of code "A"
4.Series wired remote control units have power failure
compensation.
The right figure is a remote controller, which can be used on
series
remote control units and the matching remote control receiver
1.Remote control receiver using method :
Use remote controller control the
remote control window of the remote
control receiver.
2.Series remote
controller units
please press the
botton "CODE"to choose
the program of code "B"
3.Series remote control
units
have not power failure compensation.
fig(2)
FRESH
HIGH/SO
TIMER
SET
FILTER
B
A
M
D
HEALTH
FRESH
HIGH/SO
TIMER
SET
FILTER
B
A
M
D
HEALTH
Parts and Functions
HEAT
HEAT
HEAT
HEAT
SET
ROOM
MODE
FAN
TEMP
CLOCK
SET
TIMER
SLEEP
RESET
FILTER RESET
HEALTH
SWING
C
ON
OFF
*
AUTO
ON/OFF
SET
ROOM
MODE
FAN
TEMP
CLOCK
SET
TIMER
SLEEP
RESET
FILTER RESET
HEALTH
SWING
C
ON
OFF
*
AUTO
ON/OFF
10
Health Function and Installating the Reciever
Connecting wiring method of receiver :
Refer the indoor unit wiring diagram .
Safety cautions see the electrical wiring part .
1.How to use the health function (only for units with this function)
After set the right function mode, press health button,
remote controller or wire controller displays "
",oxygen pump
or negative ion generator starts up to apply oxygen or negative
i
on to indoor unit. Press the button again,the sign "
" disapp-
eared and negative ion generator stops working. After all health
function of the indoor unit being fully canceled, oxygen pump
stopped.
On the "Health" mode, if you want
to setting timing open mode, should
close the health first: On the timing
open mode, please don't use health
function.
About health function
CAUTION:
When the temperature of the outdoor unit is lower than 4 ,
oxygen pump is automatically stopped, if press health button
just then, oxygen pump could not start up. But if the air condi-
tioner has the negative ion function simultaneous,when press
the Health button, negative ion function could still be operated.
When the temperature of the outdoor unit is higher than 6 ,
oxygen pump could automatically resume to oxygen-make
function.
1 .Emergency switch
2 .Running lamp: When the compressor working, this lamp bright.
3 .Timing lamp: When the unit been setting Timing running, this lamp bright.
4 .Power lamp: After open the unit, this lamp bright when the unite enter
health running, the lamp change from orange to blue lamp.
5 .Indoor temp. sensor: Test the room temperature.
FRESH
HIGH/SO
TIMER
SET
FILTER
HEALTH
MODE
FAN
HEALTH
TEMP
CLOCK
SET
TIMER
SLEEP
RESET
ON/OFF
AM
SET
AM
SWING
FILTER RESET
HEAT
HEAT
