Haier WJ26X27153, Руководство пользователя

Страница: 7 / 28

49-5000489 Rev. 1
7
ENGLISH
Remote Control Features and Settings
Manual Operation (POWER Button) and Maintenance
16 . AUTO
The heat pump will automatically select Cool, Heat, or Fan
operation according to set temperature. When SPEED is set
to AUTO the heat pump automatically adjusts the fan speed
according to room temperature.
17 . VACATION
10°C/50°F Heating sets the system to maintain 10°C/50°F. This
is used to prevent freezing during long unoccupied periods of
time.
18 . TIMER ON/OFF
To set the Timer using the TIMER ON button, press the CLOCK
UP/DOWN. The time will be changed by 1 minute. Press the
APPLY to confirm the setting. Press the TIME OFF button to
cancel the timer function.
19 . CLOCK
To set the clock using the CLOCK button, press the CLOCK UP/
DOWN. The time will change by 1 minute. Press the APPLY to
confirm the setting. The clock will keep the original time if the
APPLY button is not pressed in 10 seconds.
20 . APPLY
Save and Cancel the TIMER and CLOCK selection.
21 . F/C
Press F/C to switch the remote and unit display temperature
between Fahrenheit and Celsius.
22 . LIGHT Button
Turns on and off the indoor display. To display only set
temperature, press LIGHT button 10 times within 5 seconds. The
indoor will beep 3 times when successful. To return to ambient
temperature display, press LIGHT 10 times within 5 seconds
again. Default is the indoor unit displaying ambient temperature.
The set temperature will only display a for a few seconds after
adjusting it with the remote.
23 . RESET Button
If the remote control is not functioning properly, use a pen point or
a similar object to depress this button to reset the remote.
Manual Operation
• Use the POWER button only when the remote control is lost
or damaged.
• Press the POWER button and the unit will beep once,
indicating start of operation.
• The unit will run automatically in the following modes:
• While in Manual Operation, temperature and fan speed
cannot be changed, nor will it operate in timer or DRY mode.
Inserting the Batteries
1. Remove the battery cover
2. Insert 2 AAA batteries as illustrated noting battery polarity
3. Reinstall the battery cover
NOTE:
• The distance from the remote control to the receiver should
be less than 23 feet with no obstructions.
• If the remote control display is weak or the operating
distance has diminished, the batteries may need to be
replaced.
• Remote control malfunctions can sometimes be corrected
by removing the batteries from the remote for a few
minutes and then reinstalling them.
• Remove the batteries from the remote control if the unit
will not be in use for an extended period of time. If any
segments of the display remain active after battery removal,
press the reset button.
Optimizing Performance
1. Close doors and windows during operation
2. Do not block the air inlet or outlet
3. Wipe the cabinet using a soft and dry cloth. For serious
stains, use a nuetral detergent diluted with water. Wring the
water out of the cloth before wiping down the unit. Then
wipe off the detergent completely.
Cleaning the Front Cover
1. Open the front cover by pulling it upward
2. Remove the Filter:
Gently push up on the filter's center tab until it is released
from the stopper, and remove the filter in a downward
motion.
3. Clean the filter
Use a vacuum cleaner to remove dust, or wash the filter
with water. After washing, dry the filter completely.
4. Attach the filter
Attach the filter so that the "FRONT" label is facing
outward. Make sure that the filter is securly attached
behind the holding tabs. If the filter is not attached
correctly the unit may not achieve maximum efficiency.
5. Close the front cover.
Beep
emergency
operation switch
Room
Temperature
Designated
Temperature
Timer
Mode
Fan
Speed
Operation
Mode
Above 73°F 79°F No AUTO COOL
Below 73°F 73°F No AUTO HEAT