REG MODE
SET
ON/OFF
SOL H PRE INT WT HC
T-DISP
REG MODE
SET
ON/OFF
T-DISP
Ì «
Ñ ô
Ä Ü
SOL H PRE
INT WT
HC
REG
MODE
SET
ON/OFF
T-DISP
SOL H PRE
INT WT
HC
SOL H PRE
INT WT
HC
T-DISP
SET
ON/OFF
REG MODE
3
12
Note: the above parameter errors ( except power value) of the lighting area are
3%,
volume errors are
3%, and the allowed error scope of other sizes is
10%.
¼ ¯
È È
Æ ÷
° ü
× °
Ï ä
Technical parameter Packing list
Technical parameter
Packing list
Use method
Model
Volume
Water-proof
Grade
Drip-proof
Rated internal
Pressure
Size
Model
Rated voltage
Frequency
Rated Power
Input
Grass Collector area
BRF2-150W
PJF2-150W
230V~
230V~
50Hz
50Hz
2200W
2200W
0.7MPa
0.7MPa
492
530
1380(mm)
3.0m
2
4.0m
2
Drip-proof
Name of components
Packing method
Packing container
o f w a t e r t a n k
BRF2-150W
PJF2-150W
Users manual
Model
Tee joint*
Opposite wires S1/2F-3/4M
Packing of solar stage
1
3/4
fiber spacer
Collector equipment
Single-direction valve*
1
4
4
1
1
2
2
1
1
1
1
Packing of collector
Note: accessories of BRF2-150W and PJF2-150W products are suitable only for oblique
installment. For flat installment, prop stand of different angles should be made according
to requirements, which is not included in the packing accessories.The part of after which
have * will be carried by server when installation.
Water-storing tank
1
Temperature and pressure valve*
numbers.when set the parameter up to the
highest,press the setting key again,the
number will increase progressivelyfrom
the minimal number.to continually press
more than one second, the adjusted
parameter will increase progressively 3
numbers every second setting of each
parameter can be done by pressing the
setting key or by not pressing the setting
key about 6 seconds. Then the system will
automatically confirm and automatically
enter the next parameter setting, until the
system finally withdraws from the set
conditions and returns to the conditions of
the previous clock. The set order of
parameter in specific modes is as follows:
Solar energy heating mode:
Indicating clock condition---to check the
hour of clock---to check the minute of
clock---to set temperature difference of
water pump running--- indicating clock
c o n d i t i o n . F o r e x a m p l e : t e m p e r a t u r e
difference value setting of water pump
running: to press the setting key to enter
t h e s e t t i n g c o n d i t i o n o f t e m p e r a t u r e
difference of water pump running. The
indication board indicates the present set
value (the first place on the left of the clock
number tube indicates
L
, and the
following two places indicate the tacitly
approved set value, which is 15
). To
press the setting key to select between 15
and 10
. For the indication interface,
see Fig.11.
Simultaneous heating mode:
I n d i c a t i o n c l o c k c o n d i t i o n - - - t h e
temperature of heating---indication clock
condition.
Preset heating mode:
Indicating clock condition---to set hour of
`
492
530
1380(mm)
150L
150L
BRF2-150W
PJF2-150W
Affusing liquid valve*
Small expanding bolt
Large expanding bolt
Solar stage pothook
Expanging tank fixity
Expanding tank
Solar stage
Fig.9 solar heating interface
Fig.11 temperature difference
setting interface for water pump
Fig.10 turning off interface
Fig.12 Temperature setting interface for
The first time preset heating
1
2
