background image

Figure 1

7 Disposal after washing 

After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may I
nfluence  your using the machine.

Please first pull off the power plug from the receptacle before cleaning.

1.The method of dismantle:Push it up aslant and gently.

Clean the detergent box and set it on

the control panel seat.

2.The method of install : install it upwards and aslant 

                              and push it in .

Install

Dismantle

The lint filter must be used during washing.

It must be cleaned in time after each using.

The methods of dismantle and install lint filter as follows:
1.Push down the spring piece of the top lint  filter to make the claws out of the filter cover, 
and then pull out the lint filter to get it down.(See to the figure 1)
2.Pull the back of the lint filter, and then you can get down it off the front cover of the lint filter.
 (See to the figure 2)
3.Sweep the rubbish in the lint filter.
4.Put the back of the lint filter into the front cover .(See to the figure 2)
5.Put the lint filter into filter cover, and make it tight
6.Make sure the lint filter is well installed, or it can influence your use.

Filter cover

Lint filter

Figure 2

dismantle

install

The front cover of lint filter

The back cover of lint filter

The filter screen of the water inlet valve is l
ikely to be blocked  by foreign materials 
and influence the water inlet. 
Please clean it with brush every two months.

If the cabinet is dirty, wipe it with wet cloth
     Do not flush it directly with water.
     Wipe it with neutral detergent.
     Do not wipe it with thinner, petrol, alcohol etc.

Thinner

Petrol

Alcohol

1.After washing, close the water faucet.  ( If needed, you can dismantle the water inlet hose).

5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time (
about 1 hour), then close the top lid.

4.Hang up the power cord and drain hose.

3.Be sure to pull off the power plug before maintenance.

2.Do not store water in the washing machine for a long period.  Drain  the  water  completely after each using.

Содержание HWM55-0528



















Отзывы: