Haier HDBL655AFS Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 36

Haier HDBL655AFS Скачать руководство пользователя страница 30

28

NOTE: Total drain hose length must not exceed 10 ft (3.05 m), for proper drain

operation.

a

b

a

a

Hose Clamp

b

Coupler

STEP 14 - SECURE DISHWASHER

Depending on the material of your countertop, use either instructions to “Install to

Countertop” or “Install to Adjacent Cabinets” to secure your dishwasher.

Install to Countertop
The dishwasher must be secured to the countertop using the two mounting clips on

top of the dishwasher.
1. Insert the mounting clips into the front, top slots of the dishwasher.

NOTE: The top mounting clips have a break off point, so a section of the clip can

be removed, if necessary, to fit the depth of the cabinet.

b

a

c

a

Mounting Clips

b

Break Off Point

c

Tub Flange

2. Open the dishwasher door and remove lower dish rack.
3. Place a towel over the pump assembly and spray arm of dishwasher to keep

screws from falling into pump area during installation.

4.  Check that the dishwasher is level and centered side to side in the opening.
5.  Check that the tub flange aligns with the front face of the cabinet frame.
6.  Using two Phillips screws (provided), fasten the two mounting clips on the top of

the dishwasher to the underside of the countertop.

NOTE: The dishwasher must be attached to the countertop to keep it from

tipping when the door is opened.

a

a

#8 x 5/8" Phillips

Flat-Head Screw

«
...
28
29
30
31
32
...
»

Содержание HDBL655AFS





































Отзывы:

Нет отзывов