Haier HDBL655AFS Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 36

Haier HDBL655AFS Скачать руководство пользователя страница 24

22

STEP 9 – POSITION DISHWASHER UNDER

COUNTERTOP

1. Push dishwasher completely into the opening so that the front corners of the

dishwasher door are flush with the cabinet doors.

NOTE: It is all right if the dishwasher fits tightly into cabinet opening. Do not remove

insulation blanket – the blanket reduces the sound travel.

Reposition dishwasher by grasping

both sides with hands.

Do not push against front door panel

with knee. Damage to the door panel

will occur.

STEP 10 - LEVEL THE DISHWASHER

IMPORTANT: Dishwasher must be level for proper dish rack operation and wash

performance.
1. Align front of dishwasher door panel with cabinet doors. You may need to adjust

alignment to be even with your cabinets.

NOTE: Prop up one side of frame to hold dishwasher up off floor when adjusting

front legs. With some installations, it may be easier to adjust the front leg using a

6" adjustable wrench.

2. Check that the leveling legs are firmly against the door.
3. Close and latch the door, and place level against the front panel. Check that

dishwasher is plumb. If needed, adjust leveling leg or add shims until dishwasher

is plumb.

NOTE: Shims must be securely attached to floor to prevent their movement

when the dishwasher is operated.

4. Repeat for other side of dishwasher.

«
...
22
23
24
25
26
...
»

Содержание HDBL655AFS





































Отзывы:

Нет отзывов