Haier GE NF96UV Скачать руководство пользователя

Страница: 29 / 53

Page 29

31-5000726 Rev. 0

General Guidelines for Vent Terminations

In Non-Direct Vent applications, combustion air is taken

from indoors or ventilated attic or crawlspace and the flue

gases are discharged to the outdoors. The NF96UV is then

classified as a non-direct vent, Category IV gas furnace.

In Direct Vent applications, combustion air is taken from

outdoors and the flue gases are discharged to the outdoors.

The NF96UV is then classified as a direct vent, Category

IV gas furnace.

In both Non-Direct Vent and Direct Vent applications, the

vent termination is limited by local building codes. In the

absence of local codes, refer to the current National Fuel

Gas Code ANSI Z223-1/NFPA 54 in U.S.A., and current

CSA-B149 Natural Gas and Propane Installation Codes in

Canada for details.

Position termination according to location given in Figure

24 or Figure 33. In addition, position termination so it is

free from any obstructions and 12” above the average

snow accumulation.

At vent termination, care must be taken to maintain

protective coatings over building materials (prolonged

exposure to exhaust condensate can destroy protective

coatings). It is recommended that the exhaust outlet not be

located within 6 feet (1.8m) of an outdoor AC unit because

the condensate can damage the painted coating.

NOTE:

See Table 11 for maximum allowed exhaust pipe

length without insulation in unconditioned space during

winter design temperatures below 32°F (0°C). If required

exhaust pipe should be insulated with 1/2” (13mm)

Armaflex or equivalent. In extreme cold climate areas,

3/4” (19mm) Armaflex or equivalent may be necessary.

Insulation must be protected from deterioration. Armaflex

with UV protection is permissable. Basements or other

enclosed areas that are not exposed to the outdoor

ambient temperature and are above 32 degrees F (0°C)

are to be considered conditioned spaces.

Do not use screens or perforated metal in exhaust

terminations. Doing so will cause freeze-ups and may

block the terminations.

IMPORTANT

For Canadian Installations Only:
In accordance to CSA International B149 installation

codes, the minimum allowed distance between the

combustion air intake inlet and the exhaust outlet

of other appliances shall not be less than 12 inches

(305mm).

IMPORTANT

Содержание GE NF96UV






















































Результаты поиска

Содержание GE NF96UV

Отзывы:

Похожие инструкции для GE NF96UV

Бренды по названию

Популярные бренды

Haier GE NF96UV, Руководство по обслуживанию

Результаты поиска

Содержание GE NF96UV

Отзывы:

Похожие инструкции для GE NF96UV

Бренды по названию

Популярные бренды