Haier GE NF96UV Скачать руководство пользователя

Страница: 18 / 53

Page 18

31-5000726 Rev. 0

Placement and Installation

All pipe, fittings, primer and solvent cement must conform

with American National Standard Institute and the American

Society for Testing and Materials (ANSI/ASTM) standards.

The solvent shall be free flowing and contain no lumps,

undissolved particles or any foreign matter that adversely

affects the joint strength or chemical resistance of the

cement. The cement shall show no gelation, stratification,

or separation that cannot be removed by stirring. Refer to

the Table 7 for approved piping and fitting materials.

Solvent cements for plastic pipe are flammable liquids

and should be kept away from all sources of ignition.

Do not use excessive amounts of solvent cement when

making joints. Good ventilation should be maintained to

reduce fire hazard and to minimize breathing of solvent

vapors. Avoid contact of cement with skin and eyes.

CAUTION

NF96UV exhaust and intake connections are made

of PVC. Use PVC primer and solvent cement when

using PVC vent pipe. When using ABS vent pipe, use

transitional solvent cement to make connections to the

PVC fittings in the unit.

IMPORTANT

Use PVC primer and solvent cement or ABS solvent

cement meeting ASTM specifications, refer to Table 7.

As an alternate, use all purpose cement, to bond ABS,

PVC, or CPVC pipe when using fittings and pipe made of

the same materials. Use transition solvent cement when

bonding ABS to either PVC or CPVC.

Low temperature solvent cement is recommended during

cooler weather. Metal or plastic strapping may be used for

vent pipe hangers. Uniformly apply a liberal coat of PVC

primer for PVC or use a clean dry cloth for ABS to clean

inside socket surface of fitting and male end of pipe to

depth of fitting socket.

Canadian Applications Only

- Pipe, fittings, primer and

solvent cement used to vent (exhaust) this appliance

must be certified to ULC S636 and supplied by a single

manufacturer as part of an approved vent (exhaust)

system. In addition, the first three feet of vent pipe from the

furnace flue collar must be accessible for inspection.

Table 8 lists the available exhaust termination kits.

Schedule 40 PVC (Pipe)

D1785

Schedule 40 PVC (Cellular Core Pipe)

F891

Schedule 40 PVC (Fittings)

D2466

Schedule 40 CPVC (Pipe)

F441

Schedule 40 CPVC (Fittings)

F438

SDR-21 PVC or SDR-26 PVC (Pipe)

D2241

SDR-21 CPVC or SDR-26 CPVC (Pipe)

F442

Schedule 40 ABS Cellular Core DWV

(Pipe)

F628

Schedule 40 ABS (Pipe)

D1527

Schedule 40 ABS (Fittings)

D2468

ABS-DWV (Drain Waste & Vent)

(Pipe & Fittings)

D2661

PVC-DWV (Drain Waste & Vent)

Pipe & Fittings)

D2665

PRIMER & SOLVENT CEMENT

ASTM

SPECIFICATION

PVC & CPVC Primer

F656

PVC Solvent Cement

D2564

CPVC Solvent Cement

F493

ABS Solvent Cement

D2235

PVC/CPVC/ABS All Purpose Cement For

Fittings & Pipe of the same material

D2564, D2235,

F493

ABS to PVC or CPVC Transition Solvent

Cement

D3138

CANADA PIPE & FITTING & SOLVENT

CEMENT

MARKING

PVC & CPVC Pipe and Fittings

ULCS636

PVC & CPVC Solvent Cement
ABS to PVC or CPVC Transition Cement

POLYPROPYLENE VENTING SYSTEM

ULC-S636

PolyPro® by Duravent
InnoFlue® by Centrotherm

ULC-S636

ECCO Polypropylene Vent

ULC-S636

Table 7. Piping and Fittings Specifications

Содержание GE NF96UV






















































Результаты поиска

Содержание GE NF96UV

Отзывы:

Похожие инструкции для GE NF96UV

Бренды по названию

Популярные бренды

Haier GE NF96UV, Руководство по обслуживанию

Результаты поиска

Содержание GE NF96UV

Отзывы:

Похожие инструкции для GE NF96UV

Бренды по названию

Популярные бренды