background image

4

Read the precautions in 

this manual carefully before 

operating the unit.

This appliance is filled with R32.

Read the operator's manual

Service indicator, read technical 

manual

After reading this handbook, hand it over to those who will be using the unit.
The user of the unit should keep this mamual at hand and make it available to those who will be performing repairs or 

relocating the unit. Also, make it available to the new user when the user changes hands.

 WARNING

Ask your dealer or qualified personnel to carry out installation work.Do not attempt to install the air conditioner 

yourself. Improper Installation may result in water leakage, electric shocks, fire or explosion. All the cables shall 

have got the European authentication certificate. During installation, when the connecting cables break off, it must 

be assured that the grouding wire is the last one to be broken off.If refrigerant gas leaks during installation, ventilate 

the area immediately.oxic gas may be produced.if the refrigerant comes into contact with fire,and explosion may be 

happen.
Make sure ground connection is correct and reliable.Do not earth the unit to a utility pipe, lightning conductor or 

telephone earth lead. Imperfect earthing may result in electric shocks.

The breaker of the air conditioner should be all-pole switch and explosion-proof. The distance between its two 

contacts should not be no less than 3mm. Such means for disconnection must be incorporated in the wiring.

The air conditioning sockets should be placed 1m above from the air conditioner, nor under the air conditioner. Be 

sure not to use open flame, high static electrical or high temperature equipments etc.nearby the air conditioner.

Do not use means to accelerate the defrosting process or to clean, other than those recommended by the 

manufacturer.

The appliance must be stored in a room without continuously operating ignition sources, the radius of the storage area 

should be no less than 2.5 m (for example:open flames, an operating gas appliance or an operating electric heater).

Do not pierce or burn.

Be aware that refrigerants may not contain an odour.
The appliance must be installed, operated and stored in a room with a floor area larger than the Minimum Room Area 

specified in the table on the following pages,The room should be well ventilated.
Comply with national gas regulations.
This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or 

mental capabilities or lack of experience and knowledge if they have been given superivision or instruction concering 

use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. 

Cleaning and user maintenance shall not be made by children without supervision.
The air conditioner can not be discarded or scrapped Randomly If you need please contact customer service 

personnel of Haier to scrap in order to obtain the correct disposal methods.

Reusable mechanical connectors and flared joints are not allowed indoor.

 CAUTION

Do not install the air conditioner at any place where there is danger of flammable gas leakage.In the event of a gas 

leakage, build-up of gas near the air conditioner may cause a fire to break out.
Tighten the flare nut according to the specified method such as with a torque wrench.If the flare nut is too tight, it may 

crack after prolonged use, causing refrigerant leakage.
Take adequate steps to prevent the outdoor unit being used as a shelter by small animals.Small animals.making 

contact with electrical parts can cause malfunctions, smoke or fire.

Please instruct the customer to keep the area around the unit clean

The temperature of refrigerant circuit will be high, please keep the inter-unit wire away from copper pipes that not 

thermally insulated.

Only qualified personnel can handle, fill, purge and dispose of the refrigerant.

Содержание 1U160S2SP1FB





























Отзывы: