Hague MAXIMIZER 7180 Скачать руководство пользователя страница 15

Страница: 15 / 28

Models 7180 and 7380

Owner’s Manual

and Installation Guide

5/22/2019

Service Settings—5B

To program Service settings on the controller, press and hold the Select and Display buttons while “Service Settings” is

displayed until “Set Language Eng” is displayed. Programming Service Settings i

s similar to programming Customer

Settings (see

Customer Settings

for programming details). The values that can be set are listed below.

Note:

The Service Settings must be set before the Customer Settings.

Display

Meaning

Possible Values

Comments

Set Language Eng

Set the language of the
display

Set Language Eng
Entrer Langue Fra

Entre La Leng. Esp

Units ENG

Units of measure

ENG or MET

Soft. v. # X.XX

Displays the current

software version

Cannot be set

2.10 or later

Mode

Operating Mode:
Timer (Mode 1)

Demand Delayed (Mode 2)

1 or 2

See

Operating Modes

Regen Freq.

How often regeneration

occurs

–

12 days

Only displays when in Mode 1

Hard. Gr.

040

Hardness of the water that

was tested

003 to 999 Grains

(00000 to 99999 mg/L)

This is the actual hardness

reading and is not compensated
for iron and/or manganese

Iron ppm

Amount of iron in parts per
million of the water that was

tested

00 to 99 ppm (mg/L)

This value is used to calculate
compensated hardness

automatically

Mang. ppm

Amount of manganese in

parts per million of incoming

water

00 to 99 ppm (mg/L)

This value is used to calculate

compensated hardness

automatically

Salt =

Sodium Regenerant filling the brine

tank

Sodium or Potassium

See

Warning

Comp. Hard.

00070

Compensated hardness

using the hardness, iron,
and manganese settings

Cannot be set

ppm or mg/L

The formula used is:

Ha (4 x each ppm iron) +
(4 x each ppm manganese) =

compensated hardness

Capac. Gr.

22,700 The desired softening

capacity number

00000 to 99999 Grains

(0000 to 9999 gm)

See

Specifications

Mode 1

(Timer Mode) and Mode 2

(Demand Delayed Mode) Setting
Chart

for capacities based on salt

usage

–

96 hr Regen

A way to force regeneration

at regularly scheduled
intervals

No (or Yes, for iron)

See

–

96 Hour Regeneration

Backwash 1

01.0

Number of minutes the first
backwash cycle lasts

00.0 to 99.9

Set to the nearest tenth of a
minute

Warning:

When iron and/or manganese is present in the water supply, do not use potassium chloride as a regenerant.

Iron and/or manganese bacteria may develop and foul the softening media and may void the warranty.

This table continues on the next page.

Содержание MAXIMIZER 7180





























Результаты поиска

Содержание MAXIMIZER 7180

Отзывы:

Похожие инструкции для MAXIMIZER 7180

Бренды по названию

Популярные бренды

Hague MAXIMIZER 7180, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание MAXIMIZER 7180

Отзывы:

Похожие инструкции для MAXIMIZER 7180

Бренды по названию

Популярные бренды